6kN and 1.0kNm loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the principal stresses (max and min normal stresses), principal planes (orientation of plane for max-min normal stresses) and max shear stress by using Mohr's circle.

6kN and 1.0kNm loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the principal stresses (max and min normal stresses), principal planes (orientation of plane for max-min normal stresses) and max shear stress by using Mohr's circle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

Q: 100 MPa 75 MPa 150 MPa

Q: A cylinder having an internal diameter of 20 in and an external diameter of 36 in is subjected to an…

Q: Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A…

Q: Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile…

A: Concept Of Moment Inertia Used

Q: From the figure as shown, determine the stress in psi at the top surface of the second cylinder.…

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

Q: Determine the stress (in psi) in member BD if the cross-sectional area of the BD is 1.89 in2 P =…

Q: A thick cylindrical shell of internal diameter 150 mm has to withstand an internal fluid pressure of…

Q: Determine the maximum stress at the fillet of the filleted flat plate of 8 mm thickness as shown in…

Q: solid circular rods are welded together at B as shown. Determine the normal stress at midpoint AB.…

A: To determine the normal stress at midpoint AB:

Q: Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB

A: Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB.

Q: Question 2 The bar has a cross-sectional area A and is subjected to the axial load P. Determine the…

Q: a. The diameter of the connecting rod CD, given that the normal stress is limited to 140 MPa. b. The…

A: Given: P1= 5 kN Normal stress = 140 MPa To determine: The diameter of connecting rod CD The shear…

Q: 1) Reqd: Determine Maximum Shearing Stresses for the 3 segments and eat C (2)Solid 60-mm-diameter G…

Q: Q 4. Determine longitudinal stress in the cylinder if it has wall thickness of 7 mm and subjected to…

A: Given data: The thickness of the cylinder is t = 7 mm. The internal pressure is P = 100 MPa.

Q: Using Mohr's circle, determine the fol (1) the stresses acting on an element in (2) the principal…

Q: A thin hollow sphere of radius 300 mm and thickness 2.5 m is subjected to an internal pressure.…

A: Thin spherical shell is given Tensile stress in sphere = σ = 360 kPa Radius of sphere = r = 300 mm…

Q: The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses…

A: Given, I section Px =-80 kN = -80 X 103 N My=-500 Nm Mz=10 kNm =10 X 103 Nm

Q: Determine the equivalent state of stress on an element at the point which represents (a) the…

A: Given that, σx=50 MPaσy=0 MPaτ=15 MPa (a) Calculating principle stresses, Writing the formula for…

Q: Using Mohr's circle, determine: (a) The stresses acting on an element oriented at an angle 0-30°…

A: Mohr circle is a two dimensional graphical method of expressing the normal stresses and shear stress…

Q: Three forces of 500 lb, 800 lb, and 600 lb are applied to the end of the 2-in-diameter bar, as…

Q: Determine the maximum shear stress for the above stress state (ksi)

A: The matrix form of general 3D state of stress is

Q: An 8 mm thick cylindrical steel tank has an outside diameter of 600 mm and a length of 3 m. (a) when…

A: (a) The circumferential stress is 1.0889 MPa. (b) The longitudinal stress at the bottom is 0.5445…

Q: The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?

A: Assume that the bar ABCD is The load acting on the bar is P The maximum normal stress then act on…

Q: Calculate the average normal stress and determine the radius of Mohr's Circle. Then draw Mohr's…

A: Write the given data in the problem. Sx=-36 MPa Sy=-70 MPaSxy=25 MPa Here, the negative sign on…

Q: Determine the equivalent state of stress on an element at the same point oriented 60°…

A: Given Data: The value of σx=150 MPa The value of σy=100 MPa The value of τxy=75 MPa The orientation…

Q: The axial and circumferential stress experienced by the cylinder wall at mid-depth

A: Given data: Axial stress on side face will be due to force on the bottom face.

Q: The 2-in.-diameter drive shaft AB on the helicopter is subjected to an axial tension of 10 000 lb…

A: Taking the section of the 2 diameter drive, we could see that Now we find the normal stress using…

Q: The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at…

A: To find: The normal and shear stress at point B. Given: The diameter of the rod is d=0.97 in.…

Q: Determine if the stress in the steel section, aluminum section, and bronze section are compression…

Q: With the same given, if the members have a square cross-section with a diagonal of 11.31 cm and…

A: In the question, the applied magnitude of force is not given, thus it is not possible to calculate…

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

A: Given Data: The load acting on the beam is 25 kip each. The free-body diagram of the beam can be…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load…

A: Given:P=20 KNT=10.11 KN.md=75 mmdA=50 mm

Q: A 100-mm-diameter rod is subjected to the loads shown. Determine the principal stresses at point A.…

A: NOTE: According to Bartleyby's policy we shall answer only three sub-parts so kindly repost other…

Q: d) Draw Mohr's circle of stress for the shaft and from this determine the principal stresses,…

Q: required thickness of member BC and the diameter of the pins at A and B if the allowable normal…

Q: As shown in the picture below, the sloping direction of the member is subjected to a compression of…

A: given:

Q: A thin hollow sphere of radius 300mm and thickness 2.5m is subjected to an internal pressure.…

Q: Determine the equivalent state of stress for an element oriented 60° counterclockwise from the…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

6kN and 1.0KNM loads are applied to the top of the 62-mm-diameter
cast-iron as shown. Determine the principal stresses (max and min
normal stresses), principal planes (orientation of plane for max-min
normal stresses) and max shear stress by using Mohr's circle.
Hint: Use given coordinate system. So, H is on x-z plane and K is on y-
z plane
1.0 kN.m
6 kN
X
220 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the principal planes and the principal stresses for the state of plane stress resulting from the superposition of the two states of stress shown. Given: X = 60 MPa and Y = 20 MPa. Determine the orientation of the principal plane in the first and second quadrant. Determine the maximum/minimum principal stresses
The state of stress at a point in a member is shown on the rectangular stress element where the magnitudes of the stresses are |σx|=137 MPa and |τxy|=70 MPa. Determine the state of stress on an element rotated 85∘ clockwise from the element shown.
Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure.
The state of stress at a point in a member is shown on the rectangular stress element; the magnitudes of the stresses are |σx|=66 MPa, |σy|=39 MPa|, and |τxy|=71 MPa. Using the stress-transformation equations, determine the state of stress on the inclined plane AB.
The stress of member AB is equal to the stress of member BC having a diameter of 100 mm. Determine the diameter of member AB.
Use Mohr’s circle to determine the normal stress and shear stress acting on the inclined plane AB.
Determine the equivalent state of stress if an element is oriented 60° clockwise from the element shown.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 50 MN/m2 tension respectively. The shear stress across these planes is 30 MN/m? (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 30° to the plane of greater principal stress. And also verify the answer by drawing the Mohr's circle.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 55 MN/m2 tension respectively. The shear stress across these planes is 25 MN/m2 (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 25o to the plane of greater principal stress. And also verify the answer by drawing the Mohr’s circle.
Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated in the figure.
The axial and circumferential stress experienced by the cylinder wall at mid-depth (1m as shown)
Using transformation equations of plane stress, determine the normal and shear stress components for X’-axis located 0.5 radians clockwise from x-axis. The non-zero stress components are given as follows, σx= 200 MPa, σy= 100 MPa, τxy= -50 MPa.