12 mm 60 mm 12 mm 20 mm 80 mm 20 mm

Q: 14- The anchor shackle supports a cable force of 5.0 kN. If the pin has a diameter of 6 mm,…

A: Given data: The diameter of the pin, d = 6 mm. The applied load, P = 5 kN. Draw the free-body…

Q: Determine the shear force at the right end of the uniform load. Use wo = 150 N/m, a = 1.3 m; and b =…

A:

Q: The double T-beam is fabricated by welding the three plates together as shown. Determine the shear…

A: Given: The shear force acting on the beam, V = 80 kN = 80,000 N The length of the horizontal plate,…

Q: A shear force of V= 300 kN is applied to the box girder. Determine the shear flow at points D. 90 mm…

A:

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is…

A:

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings. Determine the…

A: The torque acting at A is given as : Polar moment of inertia is calculated as :

Q: Determine the maximum shear stress in the 40-mm-diameter shaft.

A: The torque on the pulley B is The torque on the pullet A is The maximum torque in the shaft is

Q: A shear force of V = 18 kN is applied to the box girder. Determine the shear flow at points A and B.

A: Section properties for given box are

Q: 20. Determine the shear force at the right end of the uniform load. Use wo = 150 N/m, a = 1.3 m; and…

A:

Q: Qi: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress…

A:

Q: The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in the…

A: Given data as per the question  diameter of shaft = 50 mm

Q: The force required to shear the bolt in a flange coupling is 7.5 kN. The bolt has a shear stress of…

A: Given information, Shear force is 7.5kN, Shear stress is 2MPa   Find , Dia of bolt d

Q: The beam is constructed from two boards fastened together at the top and bottom with three rows of…

A: Given Data: Number of nails, n=3 Space between nails, s=4 in

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: GivenP=375N

Q: The beam is fabricated from three steel plates, and it is subjected to a shear force of V = 150 kN.…

A:

Q: Determine the maximum tensile (fot) and compressive (foc) stresses (psi) developed in the…

A: Objective: To determine the maximum tensile stress fbt and compressive stress fbc.

Q: A shear force of V = 18 kN is applied to the box girder. Determine the shear flow at point C.

A: Given data: The magnitude of the shear force is; V = 18 kN. Draw the cross-section of the beam. The…

Q: The beam is subjected to a shear force of V = 160 kN. 300 mm 200 mm 20 min 90 mm A 20 mmv 20 mn Part…

A:

Q: If the applied shear force V = 18 kip, determine the maximum shear stress in the member.

A: Given data τallow=8 ksi

Q: Determine the shear stress at point H. V= 80 kN. H Q 80 [mm] 12

A:

Q: The double T-beam is fabricated by welding the three plates together as shown. If the weld can…

A: x¯=∑AxAx¯=A1x1+A2x2+A3x3A1+A2+A3x¯=(215×20)(2152)+(150×20)(150+502)+(150×20)(145+202)(215×20)+(150×2…

Q: A shear force of V= 350 kN is applied to the box girder. Determine the shear flow at points D. 90 mm…

A: Given data V=350kN

Q: Determine the largest shear force V that the member can sustain if the allowable shear stress is…

A:

Q: The brake pads for a bicycle tire are made of rubber. If a frictional force of 50 N is applied to…

A:

Q: determine the maximum shear stress that is generated through the shaft. 300 N - m 200 N- m 48 mm 0.9…

A: d1= 40 mm L1=1 m d2=44 mm L2=1.2 m d3=45 mm L3=.9 m

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Determine the…

A: Given, Load P = 250 N Load Perpendicular to AB' = Pn N Load Parallel to AB' = Ps N Length L = 300 mm…

Q: The strut is glued to the horizontal member at surface AB. If the strut has thickness of 25mm and…

A:

Q: The beam is supported by a pin at A and a short link BC. Determine the maximum magnitude P of the…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: If the load has a weight of 600 lb, determine the maximum normal stress on the cross section of the…

A: Given Data: Weight of the load is F = 600 lb. Distance between load and section is l = 1.5 ft.…

Q: A shear force of V= 450 kN is applied to the box girder. Determine the shear flow at points B. 90 mm…

A: given shear force = v= 450kN  to determine shear flow at point B figure

Q: Question 1: E The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear…

A:

Q: Q20: A cable runs from A to B around the frictionless pulley at D. If the diameter of pin at D and C…

A:

Q: Determine the maximum shear stress in the strut if it is subjected to a shear force of V = 20 kN.

A: Given data V=20 KN

Q: 90 100 mm 100 mm- 10. The average shear stress in each of the 6-mm radius bolts and along each of…

A:

Q: The hub of a flange coupling has a diameter of 135 mm. The flange has a thickness of 20 mm.…

A:

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: To know the variation and maximum value of shear force and bending moment, V and M diagram are…

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: As per given question  P=520N D=42mm L=700 mm We have to find determine shear force applied to shear…

Q: Determine the largest shear force V that the member can sustain if the allowable shear stress is…

A: Determine the y coordinate of the cross section of the given area with respect to the considered…

Q: Determine the shear stress (in Mpa) in the 27.99-mm-diameter pin at A that support the beam if P =…

A:

Q: Determine the shear stress (in Mpa) in the 30.97-mm-diameter pin at B that support the beam if P =…

A: At B, pin diameter, D= 30.97 mm P= 39.61 kN= 39.61(1000) N= 39610 N a= 2.67 m b= 4.94 m   Note:…

Q: The pin at A has a diameter of 0.25 in. If it is subjected to double shear, determine the average…

A: Let reaction force at A Ax and Ay Apply conditions of equilibrium ∑MB=0Ax(3)-600(4)=0Ax=800…

Q: Q2/ The beam is supported by a pin at A and B. Determine the average shear stress developed in the…

A: A pin support will exert both horizontal and vertical components of reaction as the reaction forces.…

Q: The beam is constructed from three boards. Determine the maximum loads P that it can support if the…

A: Draw the free body diagram of the beam shown below.

Q: . The intensity of the shear stress distribution acting over the cross sectional area needs to be…

A: Draw shear stress distribution over cross section.

Q: 30 mm - 80 kN 30 mm 2. The joint is fastened together using two bolts. Determine the required…

A:

Q: The extruded cross section is subjected to a shear force of V = 495 N. Dimensions of the cross…

A: Given Data b=42 mm d=75 mm t=3mm Ans(a)

Q: s constructed from three boards bolted together as shown in Fig. Determine the m shear stress if the…

A: Given data: Shear Force V=35 kN Spacing between each of the bolt is s=250 mm

Q: Determine the normal stress and shear stress at a point distant from hP from the bottom surface of…

A: Centroidal axis distance y= A1y1+A2y2+A3y3A1+A2+A3(1) A1=A2=(190) (10) =1900 mm2A3=(150)…

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: Given:P=395 NL=700 mmd=42 mm

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.