Determine the mean paracetamol content per tablet (in mg), using the following values: the mean absorbance 0.13, and molar absorption coefficient 9601.9 M−1 cm−1 , where the equivalent half of one tablet mass of powdered paracetamol tablets transferred is 296.4 mg and the mean paracetamol tablet weight is 599.1 mg. Give your answer to TWO decimal places (you do not need to include the units in your answer below).

Determine the mean paracetamol content per tablet (in mg), using the following values: the mean absorbance 0.13, and molar absorption coefficient 9601.9 M−1 cm−1 , where the equivalent half of one tablet mass of powdered paracetamol tablets transferred is 296.4 mg and the mean paracetamol tablet weight is 599.1 mg. Give your answer to TWO decimal places (you do not need to include the units in your answer below).

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter20: Molecular Spectroscopy And Photochemistry

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

Calculate the specific absorbance ratio (SAR), where A620 = 0.136 and A280 = 1.392. Enter your result with 3 decimal places.
A Dubosq colorimeter consists of a cell of fixed path length and a cell of variable path length. By adjusting the length of the latter until the transmission through the two cells is the same. the concentration of the second solution can be inferred from that of the former. Suppose that a plantdye of concentration 25 μg dm-3 is added to the fixed cell. the length of which is 1.55 em. Then a solution of the same dye. but of unknown concentration. is added to the second cel l. It is found that the same t ransmittance is obtained when the length of the second cel l is adjusted to 1.18 em. What is the concentration of the second solution?
Anionic surfactants in wastewater are measured spectrophotometrically as methylene blue active substances (MBAS). A volume of a water sample is first reacted with methylene blue, a cationic dye, in a basic buffered aqueous solution. The resulting solution is agitated after the addition of chloroform. The organic layer is then extracted, and the absorbance is read at 655 nm. A standard calibration curve is produced by plotting absorbance vs. concentration for the concentration range between 0 ppm to 2.50 ppm. The line had the following equation: y = 0.286x + 0.009 a. The limit of surfactant content in Philippine class B water is 300 ppb. If a 5 mL aliquot of a 50 mL water sample had an absorbance of 0.084 after MBAS analysis, is the sampled water body suitable for bathing? Support your answer
using the following information to construct a valid hypothesis addressing the effect of pH and temperature on the hydrolysis of starch. Per bench, prepare the stock amylase enzyme solution by adding distilled water to the powdered enzyme in the flask , each bench will share one flaks of enzyme solution. per groups, turn on the spectrometer and set the wavelength to 560nm.allow the instruments to warm up for at least 10 minutes. per group, set up 17 cuvettes in a Styrofoam rack. Add 3 drops of iodine (IKI) to each coveter. per group, prepare the “black” cuvette by rapidly adding 3 mL of maltose standard solution to one of The prepared cuvettes containing IKI. Rapid addition of the maltose will mix the maltose and IKI
You are measuring the concentration of an unknown protein sample, and the absorbance at 595 nm (or A595) of your unknown is greater than that of the highest-concentration standard solution. It is not advisable to simply extrapolate the line of the standard curve to calculate the concentration of the unknown In this scenario, what would be the best strategy to measure the concentration of your unknown (instead of extrapolating from the standard curve)?
A 131.7 mg sample of powdered Carbamazepine tablets was boiled with ethanol, filtered and then made up to 100 mL with ethanol. 5 mL of this solution was then diluted to 250 mL with ethanol and the absorbance at 285 nm found to be 0.486 in a 1cm path length cell.Calculate the content (% m/m) of Carbamazepine in the powder, taking A(1%, 1 cm) as 490.(State your answer to 1 decimal place and include the units)
The following data have been obtained in the calibration of a series of standards for the determination of iron, measuring the transmittance, at 506 nm and thickness of 1.00 cm of iron (II) solutions in which color with 1.10 has been developed -phenanthroline. [Fe] (ppm) 0.20 0.40 0.60 0.80 1.00 2.00 3.00 4.00 5.00 6.00 7.00 T (%) 90.0 82.5 76.0 69.5 63.5 41.0 26.3 17.0 10.9 7.0 4.5 Calculate the mean molar absorptivity of iron when determined by this method.
The absorbances of solutions containing K2CrO4 in 0.05 M KOH were measured in a 1.0-cm cell of 375 nm. The following results were obtained: Calculate the linear equation of the calibration curve.
For the determination of Fe3 +, 25 mL of sample taken from sea water is diluted to 100 mL and a quantity of the obtained solution is taken and Fe3 + is determined by atomic absorption spectrophotometer. The absorbance values of the standard and sample solutions are below, and calculate the Fe3 + concentration in sea water in mg / L by drawing the relevant graph.Solution Absorbance1 mg / L Fe3 + 0.04095 mg / L Fe3 + 0.205110 mg / L Fe3 + 0.411615 mg / L Fe3 + 0.620820 mg / L Fe3 + 0.8222Sample Solution 0.5155
Given the equation of a calibration curve y=5.63x + 0.006, identify the variable that equates to the absorbance value of the Beer's law equation.
A spectrophotometric method for the quantitative determination of the concentration ofPb2+ in blood yields an Ssamp of 0.133 for a 1 mL sample of blood that has been diluted to 6 mL. A second sample is spiked with 1 µL of a 1467 ppb Pb2+ standard and diluted to 6 mL, yielding an Sspike of 0.491. Determine the concentration of Pb2+ in the original sample of blood.
A standard curve was performed using an Absorbance spectrophotometer, and the equation of that line was determined to be y = .1563x + .025. The absorbance of an unknown was measured at .35. Calculate the concentration of the unknown according to the standard curve.