Determine the non dimensional parameters that can be employed for scaling studies in centrifugal pumps. ea scroll27Pump PerformanceBasic output parameters- Net HeadH =outWater horsepowerW = mgH = P9QHBrake horsepowerbhp = Wshaft = @TshaftNote: 1 hp = 550 ft Ibf/s = 746 W.- Pump efficiencyPump1pump =wTshaftThe pump designer tries to makea high n over as broad a rangeof discharge Qas possible.EGL /thpEGLDutum plane (z 0)28DELL

If a manufacturer produces large pumps, for testing pumps are scaled-down. Scaled-down models must…

Answered: Determine the non dimensional…

Engineering

Mechanical Engineering

Determine the non dimensional parameters that can be employed for scaling studies in centrifugal pumps

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
A 70 percent efficient pump delivers water at 20°C fromone reservoir to another 20 ft higher, as in Fig. . Thepiping system consists of 60 ft of galvanized iron 2-in pipe,a reentrant entrance, two screwed 90° long-radius elbows,a screwed-open gate valve, and a sharp exit. What is theinput power required in horsepower with and without a 6°the well-designed conical expansion added to the exit? Theflow rate is 0.4 ft3/s.
An 11.5-in-diameter centrifugal pump, running at1750 r/min, delivers 850 gal/min and a head of 105 ftat best efficiency (82 percent). (a) Can this pump operateefficiently when delivering water at 20°C through200 m of 10- cm-diameter smooth pipe? Neglect minorlosses. (b) If your answer to (a) is negative, can thespeed n be changed to operate efficiently? (c) If youranswer to (b) is also negative, can the impeller diameterbe changed to operate efficiently and still run at1750 rev/min?
The penstock of hydroelectric turbine is 0.5m x 0.5m with velocity of 5.5m/s and head of 20m. What is the output of the turbine if the turbine efficiency is 92%?
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
The head-versus-flow-rate characteristics of a centrifugalpump are shown in Fig.. If this pump drives water at20°C through 120 m of 30-cm-diameter cast iron pipe,what will be the resulting flow rate, in m3/s?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
Ina hydroelectric plant, water flows at 10 m/s in a penstock of 1.2 cross sectional area. If the net head of the plant is 30 m and the turbine efficiency is 80%, what is the turbine output?
choose the correct answer Q1A- Using water jet forces to operate turbines in hydropower plant consider application of: * a) Bernoulli’s equation b) Darcy-Weisbach Equation c) Manning equation d) Momentum equation E-none of all above B-The main difference between the flow in pipes and the flow in open channels is * a) Existing the head loss b) Existing the free surface c) Existing the pressure drop d) None of all above
Two 32-in pumps from Fig. are to be used in seriesat 1170 r/min to lift water through 500 ft of vertical castiron pipe. What should the pipe diameter be for most effi -cient operation? Neglect minor losses.
a potential hydraulic plant site average elevation of head water is estimated at 550 m tailwater elevation at 400 m water flows through a 96 cm diameter penstock and an average velocity of 4.5 m/s. If water turbine eff. is 87%, generator 96%, loss in headworks 40% of the available head, calculate the annual electrical energy the site can produce.
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?