Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1509 kJ is supplied to saline water in the steam generator to heat from 22°C to 118°C for the generation of water vapor, Take the density & specific heat of the solution as 1023 kg/m³ & 3.5 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m³)

Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1509 kJ is supplied to saline water in the steam generator to heat from 22°C to 118°C for the generation of water vapor, Take the density & specific heat of the solution as 1023 kg/m³ & 3.5 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m³)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

A cylindrical vessel (D=98,4 cm) is filled with water (ρ=1000 kg/m3, c=4.187 kJ/kg.K) to a depth of 113,64 cm. The initial temperature of the water is 15°C. Determine the time [min] required to increase the water temperature to 50°C when it is immersed into tank, filled with oil at 105°C. (NOTE: The overall heat transfer coefficient between the oil and the water is 284 W/m2.K. The surface area is 4.2 m2.)
A 0.75-m3rigid tank initially contains air whose density is 1.18 kg/m3 The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 4.95 kg/m3. Determine the mass of. air that has entered the tank.
A 10 ft³ vessel of hydrogen at a pressure of 300 psia is stirred by paddles until the pressure becomes 400 psia. Determine (a) ⧍U and (b) W. No heat is transferred, cv = 2.434 Btu/lb R Ans: ⧍U = 434 Btu; W = -434 Btu
A frictionless piston cylinder device initially contains 200L of saturated liquidrefrigerated R134a. The piston is free to move, and its mass is such that it maintainsa pressure of 900 kPa on the refrigerant. The refrigerant is now heated until itstemperature rises to 70 oC. Calculate the work done in the process.
Answer with a clean and neat solution In a piston cylinder system, the gas an initial pressure of 100 kPa and expands from 1.5 m3 to 7.5 m3 with an increase in internal energy amounting to [50 + (162/20)] kJ. Calculate the heat gain or loss in the system given the pressure volume relation as P2V is constant, where P is in kPa and V is in m3.
An electric water heater has a capacity of 2 liters. In this heater, the water is initially found as a saturated liquid at 150 kPa. When the water is in this state, the heater automatically turns on and heats the water, which expands at a constant pressure through a movable cover mechanism at the top of the heater, which has an associated work done by the system (Ws). Additionally, the electrical resistance supplies 2.2 MJ to the water. These types of heaters have very good thermal insulation and the surroundings are at normal conditions (25°C and 100 kPa). Based on this information: a) Determine the states of the working substance. b) Determine the minimum work (Wmin) with which the process can be carried out. c) Determine the exergy destroyed during this process.
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
In determining the average rate of heating of a tank of 20% sugar syrup, thetemperature at the beginning was 20°C and it took 30 min to heat to 80°C. Thevolume of the sugar syrup was 50 ft3 and its density 66.9 lb/ft3. The specific heat ofthe sugar syrup is 0.9 Btu lb-1°F-1.(a) Convert the specific heat to kJ kg-1°C-1.(b) Determine the rate of heating, that is the heat energy transferred in unit time, in SI units (kJ s-1)
A Block has the potential to produce up to 3000 MWh of geothermal energy when the project is developed to completion. In the region, the average geothermal temperature gradient is 20 °C/km, the maximum depth that can be reached using conventional drilling technology is 10 km, the average annual surface temperature is 25 °C and the rock under the surface in that region has a density of 2600 kg/m3 and a specific heat of 1000 J/kg.K. Determine the minimum mass of rock required to meet this demand.
10 kg of saturated liquid water is held in a container at 20 psi Heat is added until the water becomes a saturated vapor, determine the total amount of heat transfer (in kj) required for this to occur if A.) The process orccurs in a riddi tank B.) The preocess occurs in a piston cylinder device
Air with mass of 16 kg is heated at constant gage pressure of 9044 hPa from -24.0 °C to 184 °C. Determine the heat required in MJ. and the change of system volume
A 14-ft3 tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is rotated until the pressure inside rises to 20 psia. During the process 20 Btu of heat is lost to the surroundings. Determine the paddle-wheel work done. Neglect the energy stored in the paddle wheel. The gas constant and molar mass of oxygen are R = 0.3353 psia·ft3/lbm·R and M = 32 lbm/lbmol. The specific heat of oxygen at the average temperature of Tavg = (735 + 540)/2 = 638 R is cv ,avg= 0.160 Btu/lbm·R. The paddle-wheel work done is Btu. ANSWER