Determine the steam condition for the steam properties on the table below. Write: SHV if it is a superheated vapor SCL if it is a subcooled or compressed liquid sV if it is a saturated vapor SL if it is a saturated liquid SM if it is a saturated mixture Draw the corresponding T-s and p-v diagrams to determine the steam condition. STEAM PROPERTIES STEAM CONDITION 1. 15 MPa and 200°C 2. 3 MPa and v = 1.32 m/kg 3. 100 kPa and x = 90% 4. 30 MPa and s = 5.3500 kJ/kg-K 5. T= 300°C and s = 2.8000 kJ/kg-K

Determine the steam condition for the steam properties on the table below. Write: SHV if it is a superheated vapor SCL if it is a subcooled or compressed liquid sV if it is a saturated vapor SL if it is a saturated liquid SM if it is a saturated mixture Draw the corresponding T-s and p-v diagrams to determine the steam condition. STEAM PROPERTIES STEAM CONDITION 1. 15 MPa and 200°C 2. 3 MPa and v = 1.32 m/kg 3. 100 kPa and x = 90% 4. 30 MPa and s = 5.3500 kJ/kg-K 5. T= 300°C and s = 2.8000 kJ/kg-K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

We have a closed system containing water at a pressure of 0.2 bar. The specific volume is 924.278 cm3/g. For this vapor-liquid mixture, report the fraction of vapor. Use the steam tables and report your answer to three decimal places.
The diagram presented represents a thermodynamic process experienced by 27.5mmol (millimoles) of a monatomic ideal gas. The volume axis is divided into equal increments υ0=777cm3 while the pressure axis is divided into equal increments p0=0.301atm. Part (a) How much work, in joules, does the gas perform on its environment during the thermodynamic process represented in the diagram? Part (b) What is the change, in joules, of the internal energy of the gas during the process represented in the diagram? Part (c) How much heat, in joules, is absorbed by the gas during the process represented in the diagram?
The fluid is heated from 125 degrees Fahrenheit to 225 degrees Fahrenheit. Consider an ideal gas with the following characteristics: R = 85 ft-lbf/lbm-R Cp = 0.35 + 0.000325T BTU/lbm-R If the heating is at constant pressure, (e) the value of k at 160 degrees Celsius. If the fluid undergoes an isentropic process, determine (f) non-flow work and (g) steady-flow work. (For item f and g, use the value of k at 160 degrees Celsius).
A large mining company was provided with a 3000 cm3 of compressed air tank. Air pressure in the tank drops from 700 KPa to 180 KPa while the temperature remains unchanged at 28 deg Celcius. What percentage has the mass of air in the tank been reduced? a.72% b.78% c.74% d.76% show your complete solution
A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi gauge and 82°F. After some amount of acetylene was used, the pressure was reduced to 190 psi gauge and the temperature was 74°F. The gas constant of acetylene is 59.35 ft-lbf/lbm-°R. Determine the following: What is the initial mass in lbm of the acetylene inside the vessel What proportion in percentage of acetylene was used? What volume in ft3 would the used acetylene occupy at 30 psig and 80°F?
A piston-cylinder assembly contains a mystery substance that undergoes a series of processes. Process 1-->2: Constant pressure process at 5bar from v1=.07m3/kg to v2=.12m3/kg Process 2-->3: Constant volume process to saturated vapor Process 3-->4: Constant temperature process to quality of 50% Process 4-->5: Constant volume process to 5bar Sketch the processes on Pt, Pv, and Tv, plots. Lable the axes including property values; use closed dots to show the states, use solid lines to connect the states, add number and arrows to make clear the states numbers and process directions. Could this be considered a thermodynamic cycle? Why or why not?
A piston/cylinder arrangement contains 2 kg of ammonia at a temperature 132.45 ℃ and a pressure 5 MPa. The piston floats. Heat is added to the system until the temperature of ammonia reaches 416.37 ℃. (a) Determine the phase of ammonia during the whole process (from the initial to the final state). [Hint : Use the tables in App. 5]. b) Show the initial and final points of the process in a T-s and p-v diagram. In both diagrams sketch the dome. Show these two points relative to the dome. (c) Determine the initial and final volume of the piston/cylinder arrangement using tables. (d) Determine the useful work and the heat transfer using tables
Water at 210°C is heated, which increases the internal energy of the water by 1000 kJ/kg. Initially the quality of the system is 0.9. What is the final temperature, in °C, if the final pressure is 1.8 MPa? Report your answer to one decimal place.
***Please show your correct and complete solution for this problem. Box your final answers and express in two decimal places. Sketch the schematic diagram.*** A rigid tank initially contains 5kg of saturated vapor steam at 150°C. Heat transfer is done until the pressure of steam reaches 1.20 MPa. Sketch the P-v diagram. Solve for the change in enthalpy and heat transferred.
A piston-cylinder assembly contains 1kg of water, initially occupying a volume of 0.25mm^3 at3 bar. Energy transfer by heat to the water results in a process at constant pressure to a finalvolume of 0.6058m^3. You may assume that any kinetic and potential energy effects arenegligible.Question:(a) Sketch the process on a T-V diagram with all the features clearly labelled(b) Evaluate the work for the process(c) Evaluate the heat transfer
An air bubble rises from the bottom of a well where the temperature is 25oC, to the surfacewhere the temperature is 27oC. If the depth of the well is 5m and the atmospheric pressure is101.325kPa, determine the following:a. Initial pressure inside the air bubble (P1). b. Volume of air bubble at state 1. c. Volume of air bubble at state 2. d. Percent increase in volume of the bubble.
Five kilograms of water at 35 degrees Celsius are placed in a piston under 5.335MPa (State 1). Heat is added to the water at constant pressure until the piston reaches a stop at a total volume of 0.035 m3 (State 2). Most heat is added at constant volume until the temperature of water reaches 322 degrees Celsius (State 3). Determine (a) the quality of fluid and the mass of the vapor at State 2, and (b) the pressure of the fluid at State 3.