Derive the labor and equipment cost for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices.1. Team and Daily Rates1- Project Engineer (P 2000/day)1 - Construction Foreman (P 1000/day)6 - Mason (P800/day)12 - Laborer (P500/day)2. Output of team is 13.5 cu.m per day.3. Equipment (minor tools) is 10% of the labor cost. Determine the total number of days the team can complete the installation of the 1,000 sq.m 4" thick masonry wall using 1:5 mortarmixture.078 Determine the total cost of labor and equipment for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the followingcrew team composition, output and given prices.281,296.28280,296.28279,296.28288,296.28

we can calculate the labor cost per day for the crew team composition:Project Engineer: P…

Determine the total number of days the team can complete the installation of the 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture. 07 8 Determine the total cost of labor and equipment for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices. 281,296.28 280,296.28 279,296.28 288,296.28

Determine the total number of days the team can complete the installation of the 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture. 07 8 Determine the total cost of labor and equipment for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices. 281,296.28 280,296.28 279,296.28 288,296.28

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter8: Cast-in-place Concrete

Section: Chapter Questions

Problem 21RQ

See similar textbooks

Similar questions

Using a waste factor of 7 percent, determine the number of cubic yards of concrete needed to pour the continuous footings shown in Figures 11.36 and 11.37. Assume that the wall is centered over the footing.
Determine the weight of rebar reinforcement for the tunnel concreting works per specifieddiameter, using the following considerations:a. Rebars are assumed at 150 kg per cubic meter of concrete.b. Proportions:i. 32-mm dia. Rebar = 30%ii. 25-mm dia. Rebar = 25%iii. 20-mm dia. Rebar = 20%iv. 16-mm dia. Rebar = 15%V. 10-mm dia. Rebar = 10%
One way slabs 12 shown in Fig.1 is composed of three panels and supported by brick wall. Given: fc'= 28 Mpa, fy=400 Mpa, L = 5230 mm, thickness of Tilling and mortar =0.034 m, Live load = 2.42 KN/m, Find slab thickness
Calculate the stress at failure of a 50-mm mortar cube that failed at 35 586 N.
Determine the maximum aggregate size (MAS) for an 18" wide foundation wall that has two layers of rebars. It is comprised of number 4 rebar at 6" on center in the horizontal direction and number 6 rebar spaced at 2" on center in the vertical direction. It has 1.5" clear cover on the side of the wall
Now there is a roof beam, its height h=500mm, span L=4m, beam support length is 240mm, the wall thickness t=240mm, the design value of masonry compressive strength f=1.5 MPa, then the question is what is the eccentricity e of the wall top section under the roof beam?
Q Using the picture as a guide, create a detailed estimate for a R.C.C. cantilever retaining wall that is 30 metres long.18. The weight of 10mm-diameter bars is 0'62 kg/m and that of 12mm-diameter bars is 089 kg/m. 20mm dia. and 1:58 kg/m yield 2:47 kg/m. To create the estimate, use the following rates: (1) R.C.C.work (1:2:4), including centering and shuttering bat, excluding reinforcement—Rs. 410 per cu m. (2) M. S. reinforcement costing Rs. 550 per quintal, including cutting, hooking, etc.
Samples of perforated brick (7x11x23) cm have been tested for compression and the results are as follow: Failure |(kN): 455, 430, 405, 480, 380, 470, 380, 420 ,455, 480, 555 Absorption (%): 22, 24, 23, 22, 26, 21, 20, 20, 21, 24 Efflorescence: Light for all specimens What is the grade of this brick & can be used in foundation according to ISS?
Q3 Eor the solid slabs shown in Fig (3). find the spacing of (4 12 mm ) bars required at the locations and directions that idicated by the arrows? Assume - f =30 MPa . Fy =400 MPa Slab thickness = 150 mm Col 35+35 e o Al columas are square of 350 ma = 350 mm T
The submerged brick shown is balanced by 2.54 kg mass on the beam scale. What is the specific weight of the brick, if it displaces 2.197 liters of water.
A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL= 306 kN LL = 241 kN Li Pc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA
Given the image, a.) determine the number of bags of cement required to construct the wall footing using class A. b.) A 7m will be constructed, determine the total bags of cement required if the wall is 4.2m high and the CHB used are 5". Use class C mixture.