Q4: Three pipes A, B and C, are interconnected as shown in figure (4). Thepipes characteristicsare as follows.L (m)f6000.02B4800.032C12000.042Find the flow rate at which water will flows in each pipe, also find thepressure at point (P).PipeEL. 60mWaterBFigure (4)D (cm)151020PEL.36mCEL.15mwater

Answered: Image /qna-images/answer/92be320a-ee57-4c83-9894-ec2baaa6d314.jpg

Q4: Three pipes A, B and C, are interconnected as shown in figure (4). The pipes characteristics are as follows. Pipe L (m) A 600 B 480 C 1200 Find the flow rate at which water will flows in each pipe, also find the pressure at point (P). EL. 60m A B Figure (4) D (cm) 15 10 20 P EL.36m C f 0.02 0.032 0.042 EL.15m water.

Q4: Three pipes A, B and C, are interconnected as shown in figure (4). The pipes characteristics are as follows. Pipe L (m) A 600 B 480 C 1200 Find the flow rate at which water will flows in each pipe, also find the pressure at point (P). EL. 60m A B Figure (4) D (cm) 15 10 20 P EL.36m C f 0.02 0.032 0.042 EL.15m water.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 60-cm water pipe carries a flow of 0.1 m³/s. At point A the elevation is 50 meters and the pressure is 200 kPa. At point B, 1200 meters downstream from A, the elevation is 40 meters and the pressure is 230 kPa. The head loss , in feet, between A and B isA. 6.94B. 15.0C. 20.88D. 100.2
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
Water is pumped between two reservoirs in a pipeline with the following characteristics; (d= 300mm, L= 70m, /= 0.025, minor loss coefficient: YK=2.5). The pump performance curve is approximated by the equation: H,=22.9-650° Where H, is in meters and Q is in m's. Determine the discharge Q and pump head A when two pumps in series are used for total static head (4Z=25m).
The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm, L= 50m, = 0.02, minor loss is neglected. The pump performance curve is approximated by the equation: H,=21.5-6507 Where H, is in meters and Q is in m/s. Determine the discharge O and pump head /7 when two pumps in series are used for total static head (4Z=25m).
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe isused to move the water from an elevation of 30 m to 40 m. The pressure at section 1 is 70kPa gauge, and the pressure at section 2 is 350 kPa gauge. What power in kilowatts and inhorsepower must be supplied to the flow by the pump? Assume h L = 3 m of water and α 1 =α 2 = 1. Find the following Draw the Schematic diagram Drive the energy equation Calculate pump head Power requirement
For the system-Water at 20°C flows by gravity through a smooth pipe fromone reservoir to a lower one. The elevation difference is 60 m.The pipe is 360 m long, with a diameter of 12 cm. A pump, which delivers15,000 W to the water, is used at night to refill the upper reservoir. The pipe diameter is increased from 12 cm toprovide more flow. If the resultant flow rate is 90 m3/h, estimatethe new pipe size.
Water flows through a 2.5 cm pipe at115 L/minand o.15 bar pressure. It vents vertically 1 mabove the pipe. How high will the water shootfrom the vent?
The 30o directional pressure pipe elbow in the vertical plane is 60 cm in diameter. from the elbowThe flow rate of the current passing is 1 m3/s. At the lower end (1) of the elbow, the pressure is 70 kPa and the ground level is 30 m, the upperAt the end of the section (2), the ground level is 31 m. The fluid is water (ρwater=1000 kg/m3), frictionless and incompressible.taking into account thata) Find the velocities in sections (1) and (2) and the pressure in section (2).b) The weight of the pipe at the elbow is 1400 N. In case the length between sections is 1.2 mIn order to keep the elbow stable, taking into account the mass of water in the elbow, in the vertical directionCalculate the force that must be applied.