Rod AB is attached to collars at its ends by ball-and-socket joints. Collar A has a speed vA = 4 m/s.Assume the angular velocity of the rod is directedperpendicular to the rod. (Figure 1)Figure1 of 12 mAB1.5 m1m1.5 m Determine the y and z components of the speed of collar B at the instant z = 2 m using scalar notation.Express your answers using three significant figures separated by a comma.ΑΣφvec1] ?(vB)y, (vB): =m/s

It is required to determine the y and z components of velocity of collar B.

Answered: Determine the y and z components of the…

Determine the y and z components of the speed of collar B at the instant z = 2 m using scalar notation. Express your answers using three significant figures separated by a comma.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prop shaft of a heavy duty truck has two bearings which are positioned at 3 meters from each other. The shaft must rotate 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of 10 kg and 5 kg acting at the extremities of the arms 0,45 m and 0,6 m long, respectively. The planes in which these masses rotates are 1,2 m and 2,4 m, respectively, from the left end bearing supporting the shaft. The angle between the arms is 60 degrees. If the masses are balanced by two counter-masses named X and Y rotating with the shaft acting at a radius of 0,3 m and placed at 0,3 m from each bearing centre. 1.Draw a diagram illustrating the position of masses on the shaft. 2.Calculate the dynamic force in Newtons 3.Calculate the moment acting on the shaft in Newton-metre.
Hi there, could I please have some help solving the question below. Thank you very much in advance. A particle of mass 4.9 kg is traveling on a constant 8.7m radius with a tangential speed of 1.4e-0.125t m.s-1. 1. Determine the rotational speed of the mass at t=2.6 seconds. 2. Determine the tangential force at t=2.6 seconds. 3. Determine the normal force at t=2.6 seconds.
Consider a person holding a vacuum cleaner (idealized as Bar AB). The point where the person holds the handle (point A) is constrained to move along the vertical and has a velocity of 0.12 m/s downwards and is increasing its speed at a constant rate of 0.4 m/s2. This is to move the tail end (Point B) of the cleaner. The tail end of the cleaner has a velocity of 0.0840 m/s to the right and the vacuum cleaner has an angular velocity of 0.0586 rad/s.a) What is the the magnitude of the angular acceleration of the vacuum cleaner (Bar AB)? (1.313, 3.5, 0.875, 1.969) b) What is the magnitude of the acceleration of block B? (0.521, 0.270, 0.1929)
A particle of mass 0.102 kg is rotating at 840 rpm at a radius of 135 mm. At t=2 the radius begins to expand at a rate of 14 mm.s-1. What is the radial force at t=1.9s [N] What is the arc length traveled by the mass at t=1.9 s? [m] What is the transverse force on the mass at t=4s? [N]
Two propellers of lengths and masses l, L and m, M rotate in the same direction, as shown in the figure. if the left propeller starts from rest, w1=0 and the right propeller starts with an angular velocity that the right propeller ends up with after both propellers have collided.
1.1 What limits the rotational speed of a propeller? 1.2 What thrust is obtained from a propeller 3m in diameter that has the characteristics given in 1.1 when the propeller is operated at an angular speed of 1400 rpm and an advance velocity of zero? Assume density (p)= 1.05 kg/m^3
Four masses A, B, C and D are attached to a shaft and revolve in the same plane. The masses are 24 kg, 20 kg, 21 kg, and 18 kg, respectively and their radii of rotations are 50 cm, 50 cm, 60 cm and 30 cm. the angular position of the masses B, C, and D are 60º, 135º and 270º from the mass A. the shaft is rotating with a constant angular speed ω = 500 rpm. We need to find : 1. The magnitude and direction of the resultant inertia force before balancing 2. The magnitude and direction of the balancing mass at a radius of 10 cm The magnitude of the resultant force, in Newton, before balancing is = The direction of resultant force before balancing measured in degree CCW from the mass A is = The magnitude of the balancing mass in kg is = The direction of the balancing mass measured in degree CCW from the mass A the magnitude of resultant force after balancing is =
A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long,respectively. The planes in which these masses rotate are 1.2 m and 2.4 mrespectively, from the left end bearing supporting the shaft. The angle between the arms is 60°. If the masses are balanced by two counter-masses (named X and Y) rotating with the shaft acting at a radius of 0.3 m and placed at 0.3 m from each bearing centre:2.1. Draw a diagram illustrating the position of masses on the shaft. 2.2. Calculate the dynamic force in Newtons. Tabulate the results. 2.3. Calculate the moment acting on the shaft in Newton-metre. Tabulate the results.
An engine is attached to an inertia steering wheel, which exerts a torque moment M=20e-0,1t from rest in t = 0 s. If the steering wheel has a mass of 10 kg and a turning radius of 30 cm. Determine: a) What is the maximum angular speed that the steering wheel can reach? Thank you.
A hoop of radius 95mm and mass 100g is rotated via a capacitor driven power source with P(t)=1.61e-1.3tW. (since it is a hoop, it is a special case, and r=rG) Assuming the hoop is accelerated from rest, determine the rotational velocity after t=8.5s. [rad.s-1] Determine the rotational speed of the hoop after t=8.5s if the power source acts to roll the particle from rest on a horizontal surface. [rad.s-1]
A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long, respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively, from the left end bearing supporting the shaft. The angle between the arms is 60°. If the masses are balanced by two counter-masses (named X and Y) rotating with the shaft acting at a radius of 0.3 m and placed at 0.3 m from each bearing centre:
A particle of mass 133 kg is traveling on a constant radius 1.1 m with a angle of 0.23*sin(0.35t). 1. What is the transverse speed at 2.6 seconds? [m.s-1] 2. What is the radial force at 2.6 seconds? [N] 3. What is the transverse force on the particle at 2.6 seconds? [N