Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a prescribed tension when used for connections. (Figure 1) Figure 3 mm < 1 of 2> Part A If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact area on each head of 2.1 mm², determine the tension in the bolt shank. The material has the stress-strain diagram shown. (Figure 2) Express your answer to three significant figures and include appropriate units. T- Submit H Value µA + Request Answer → Ć Units < Return to Assignment Provide Feedback ?

Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a prescribed tension when used for connections. (Figure 1) Figure 3 mm < 1 of 2> Part A If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact area on each head of 2.1 mm², determine the tension in the bolt shank. The material has the stress-strain diagram shown. (Figure 2) Express your answer to three significant figures and include appropriate units. T- Submit H Value µA + Request Answer → Ć Units < Return to Assignment Provide Feedback ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.5P: An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The loads shown are service loads. A36 steel and 5⁄8-inchdiameter, Group A bolts will be used. If slip is permissible, how many bolts are required? Each bolt centerline shown represents a row of bolts in the direction of the width of the plates.
In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded screw Acme with major diameter (1 in) is used with coefficient of friction (0.2135). If booth screw and nut are made from 1030 - hot rolled Carbon Steel. Determine: 1- The tightening and loosening torques. 2- Thread screw and nut shear safety factors in case of double threads are in engagement. 3.3 in 2 7.2 in 32 3 in hinge
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
Figure below shows a bolted and doweled joint eccentrically loaded in shear. The bolts and dowel pins are used to connect the two parts. The shear loads are taken by the dowel pins, the sizes of which are: dA = 0.375 in, dB = 0.375 in, dC = 0.250 in, dD = 0.250 in, dE = 0.250 in. Dowels with diameters of zero are not present. Though the figure shows 5 dowel pins, that is not the case if some dowels are with zero diameters. Assume that a = 4 in, b = 4 in, l = 10 in, P = 2500 lb. Suppose that all of the dowels will take all the shear loading and will share the load equally. Assume that one part is allowed to rotate slightly about the centroid with respect to the other part. Part A Find the magnitude of the total shear force acting on dowel A. Express your answer in pounds to three significant figures. Part B Find the direction angle of the total shear force acting on dowel A measured counterclockwise from the positive x axis. Express your answer in degrees to three…
A bicycle chain consists of a series of smalllinks, where each are 12 mm long between the centersof the pins (see figure). You might wish to examinea bicycle chain and observe its construction.Note particularly the pins, which have a diameterof 2.5 mm.To solve this problem, make two measurementson a bicycle (see figure): (1) the length L of the crankarm from main axle to pedal axle and (2) the radius Rof the sprocket (the toothed wheel, sometimes calledthe chainring).(a) Using your measured dimensions, calculatethe tensile force T in the chain due to a forceF = 800 N applied to one of the pedals.(b) Calculate the average shear stress τaver in the pins.
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
1.1.7.5 Hint: Determined as the lowest load considering all of the allowable compressive load of spar, shear stress of pin, and pressure stress of pin and connecting plate.
Q - 4) In buckling experiment a steel column ( E - 210 Gpa ) was examined in pin - fixed method . It endured a load up to 1190 N. Its length is 600 mm cross sectional width is 20 mm , thickness is 4 mm. Find the critical stress and compare it with the actual stress (error %).