I need the answer as soon as possible P2 and R. Ifnecessary (when residual ripple of the power supply unit > I mV),input A ofincrease the output voltage of the power supply unit to 20 V and smoothadditionally with Ry and the Zener diode ZPD 10.Discussion:1. How large is the phase shift between Un and Uout?nt of the2 How large is the phase shift between Un and Uoui2 ?rage.3. What is the relationship between the individual gain factors and the total gainfactor?4. What is the upper and lower cut-off frequency and plot these curve by usingBode plot (use semilog paper)?ge at theroltage ata Fig (1).5. Calculate the i/p impedance of both stages?gger the6 How could the increase the number of stages effect the frequency bandwidthand gain of the whole circuit ? Explain.tatal gain

Discussion: L How large is the phase shift between Uin and Uoutt? 2 How large is the phase shift between Un and Uou2 ? 3 What is the relationship between the individual gain factors and the total gain factor? 4. What is the upper and lower cut-off frequency and plot these curve by using Bode plot (use semilog paper)? 5 Calculate the ip impedance of both stages? 6 How could the increase the number of stages effect the frequency bandwidth and gain of the whole circuit ? Explain.

Discussion: L How large is the phase shift between Uin and Uoutt? 2 How large is the phase shift between Un and Uou2 ? 3 What is the relationship between the individual gain factors and the total gain factor? 4. What is the upper and lower cut-off frequency and plot these curve by using Bode plot (use semilog paper)? 5 Calculate the ip impedance of both stages? 6 How could the increase the number of stages effect the frequency bandwidth and gain of the whole circuit ? Explain.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
4) Which of the materials created by bringing together semi-ilyletken slices of different types of additives (P and N) as follows is not used as transitors? A)NPNB)PNC)PNNPD)NPPNE)PNP
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
A 1N4733 zener diode has a Zz of 7 ohms. Considering the data of the manufacturer's hona, the Vz = 5.1 V with a test current, Iz, of 49 mA. What is the voltage across the zener terminals when the current is 65 mA? When the current is 25 mA? Include the graph where these values are shown.
write down the formulae for 3-phase fully controlled,full wave rectifier with inductive load for the following parameters: Average DC voltagerms voltagepeak inverse voltagerms currentaverage DC currentefficiencyfiring angleextinction anglepower outputpower inputform factorripple factordistortion factortotal harmonic distortiondisplacement factorpower factor of rectifier. Please answer all subpart...
We consider a half-infinite bar of p-type silicon, as shown in the figure below, with a "minority carrier digester" at (x=0), such that the electron concentration, np, at this location is zero (i.e., np(x=0)=0). This bar is uniformly illuminated and as a result carriers are generated at a rate g′. The electric field in the bar is zero and we consider a steady-state situation. The expression for the excess minority carrier concentration as a function of x is given by:
how to derive this formula? Bdc= Ic/Ib=hFE
13)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
Discuss the importance of voltage regulation in power systems.
A diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms) source of supply. Calculate the peak load current, dc load current. and determine the percent regulation from no load to the given load. a.) Peak Load Current= 120.8mA; DC load current=25.5mA b.) Peak Load Current= 133.3mA; DC load current=29.4mA c.) Peak Load Current= 144.3mA; DC load current=34.7mA d.) Peak Load Current= 152.5mA; DC load current= 48.5mA
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.