dissolved and diluted to 300 mL with water. A 20 mL aliquot was A 15.00 g sample containing mixed alkali and other inert components titrated with 5.02 mL of 0.5352 M HCI to reach PHP endpoint. Another 20 mL aliquot was titrated to the BCG endpoint, using up 18.87 mL of titrant in the process. What is/are the component/s of the sample? O NAOH only O NaHCO, only O NazCO, only O NAOH and NazCO3 O NaHCO, and Na CO3

dissolved and diluted to 300 mL with water. A 20 mL aliquot was A 15.00 g sample containing mixed alkali and other inert components titrated with 5.02 mL of 0.5352 M HCI to reach PHP endpoint. Another 20 mL aliquot was titrated to the BCG endpoint, using up 18.87 mL of titrant in the process. What is/are the component/s of the sample? O NAOH only O NaHCO, only O NazCO, only O NAOH and NazCO3 O NaHCO, and Na CO3

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter31: Introduction To Analytical Separations

Section: Chapter Questions

Problem 31.19QAP

See similar textbooks

Similar questions

A 25.00mL wastewater sample was analyzed for its Mg2+ content using a standard gravimetric method. the sample was diluted to 3.00L and an 11.00mL aliquot was treated to precipitate magnesium as MgNH4PO4.6H2O using (NH4)2HPO4 as the precipitating agent. the precipitate was then filtered, washed, dried, and ignited resulting in a 0.1325mg Mg2P2O7 residue. How much Mg (in ppm) is present in the original sample
An impure sample of calcium carbonate with a mass of 7.95 g was reacted with 50.00 cm3 of 1.00 mol dm hydrochloric acid (an excess). The resulling solution was transferred to a volumetric flask and titrated with 11.10cm3 of 0.300 mol dm-3 sodium hydroxide solution. Determine the percentage purity by mass of the calcium carbonate sample.CaCO3 + HCl -> CaCl2 + H2O + CO2 HCl + NaOH -> NaCl +H2O a. Determine how many moles of hydrochloric acid were used.b. Determine how many moles of excess HCI was titratedc. Determine how much in moles calcium carbonate present in the sample.d. Calculate the mass of calcium carbonate presente. Determine the percentwge calcium carbonate is in the sample.
A spent 1.0 percent caustic soda solution (ρNaOH = 8.42 lb/gal) with a volumetric flow rate of 3.0gpm is to be neutralized using either sulfuric acid or hydrochloric acid. First, determine the massflow rate (lb/day) of NaOH in the spent caustic soda solution, and then use that value todetermine the stoichiometric amounts (lb/day) of:1. H2SO4 required for neutralizing the OH− ions contributed by the spent caustic soda.[Hints: (1) write the balanced chemical equation for the acid-base reaction betweenNaOH and H2SO4, and use it to establish the stoichiometric weight ratio H2SO4 : NaOH.]2. HCl required for neutralizing the OH− ions contributed by the spent caustic soda. [Hints:(1) write the balanced chemical equation for the acid-base reaction between NaOH andHCl and use it to establish the stoichiometric weight ratio HCl : NaOH.]
The standard addition method is used to analyze a sample of a river water for mercury. Solution A is made by pipetting 5.00 mL of undiluted sample in to a 10 mL volumetric flask and filling to the mark with DI water. Solution B is made by pipetting 5.00 mL of undiluted sample and 3.00 mL of 15.0 ppb of Hg standard into same 10.0 mL volumetric flask and filling to the mark with DI. Solution A and B are analyzed using atomic absorption spectroscopy and give a percent transmittance values of 56 % and 33 % respectively (not blank corrected). A blank has a transmittance of 96%. What is the corrected absorbance of both solution A and B? A. Solution A: 0.123 Solution B: 0.463 B. Solution A: 0.463 Solution B: 0.234 C. Solution A: 0.123 Solution B: 0.234 D. Solution A: 0.234 Solution B: 0.463
A sulfuric acid spill occurred on the highway after a truck containing barrels of sulfuric acid swerved out of control from a truck tire blowout. Luckily no one got hurt in the event but there is a concern that the sulfuric acid spill may affect local ground water supply. A sample of the ground water in that area was recovered to assess the extent of contamination of the ground water supply. In order to determine the concentration of sulfuric acid in the sample, 25.00 mL of the ground water sample was titrated with 0.133 M NaOH and you get the following data: Sodium hydroxide (initial buret reading) 0.66 mL Sodium hydroxide (final buret reading) 17.42 mL Calculate the molarity of sulfuric acid in the ground water sample. Enter numerical answer. Report in 3 sig figs. Show work
A concentration of toxic metals in plant tissue is often found by combusting the material in a furnace and then dissolving the ash in concentrated acid. A 0.5124-gram sample of leaves was combusted to ash and transferred to a 150-mL beaker. A 25-mL portion of concentrated HCl was added and the mixture was heated on a hot plate. Three 5-mL portions of concentration HCl were added over approximately 10 minutes with continued heating in between additions. The resulting mixture was cooled to room temperature and filtered into a 50-mL volumetric flask, which was brought to volume using distilled water and mixed well. From this stock solution, a 10-mL portion was pipetted into a clean 50-mL volumetric flask, brought to volume with distilled water, and mixed. This final solution was analyzed and found to contain 12.1 ppm lead. What are the mass percent of lead in the original plant tissue?
A 15.0% by weight solution was prepared using 90.0g of KCl and the resulting density of the solution is 1.101g/mL. (MW KCl 74g/n). volume of solution(mL)? milliosmole of solute? %w/v? weight of solvent(g? N?
The total cation content of natural water is often determined by exchanging the cations for hydrogen ions on a strong acid ion-exchange resin. A 25.00 mL sample of a natural water was diluted to 100.00 ML with distilled water, and 2.06 g of a cation - exchange resin was added. After stirring, the mixture was filtered and the solid remaining on the filter paper was washed with three 15.00 mL portions of water. The filtrate and washings required 16.30 mL of 0.0282 M NaOH to give a bromocresol green end point. a) Calculate the number of millimoles of cation present in exactly 1.00 L of sample. b ) Report the results in terms of milligrams of CaCO3 per liter. Only typed solution.
A stock solution of potassium permanganate (KMn04) was prepared by dissolving 13.0g KMn04 with DI in a 100ml volumetric flask and diluting to the calibration mark. Determine the molarity of the solution.
A 100 g soil containing 20% smectitie mineral matter was mixed with 150 mL solution containing 0.10 M Pb. CEC of pure smectitie is 110 emol(+)/kg. CEC of the soil (cmol(+)/kg) is:
Although other solvents are available, dichloromethane(CH₂Cl₂) is still often used to “decaffeinate” drinks because thesolubility of caffeine in CH₂Cl₂ is 8.35 times that in water.(a) A 100.0-mL sample of cola containing 10.0 mg of caffeine is extracted with 60.0 mL of CH₂Cl₂. What mass of caffeine re-mains in the aqueous phase? (b) A second identical cola sampleis extracted with two successive 30.0-mL portions of CH₂Cl₂.What mass of caffeine remains in the aqueous phase after each extraction? (c) Which approach extracts more caffeine?
Six 50.0 ml volumetric flask 1 through 6 are labeled. 10.00 ml of 2.00 x 10-1 M Fe(NO3)3 solution was then pipet into each volumetric flask. A 1.00,2.00,3.00,4.00 and 5.00ml of 2.00 x 10-3M NaSCN solution was then pipetted to flask 2 through 6 respectively. A sufficient amount of 0.10 M nitric acid was then added to each flask to make each a total volume of 50.00ml. Hint M1V1=M2V2 a)what would be the concentration of Fe(NO3)3 in 0.10M HNO3? b)what would be the concentration of NaSCN in 0.10M HNO3?