i need the answer quickly 3. In an auto employing the Ackermann Steering gear, thesidelinks make (2.') with the Vertical. The wheel base is (2.6m)and the distance bet ween king pins is (1.6m).af the auto is desired to turn about an average radiusofrotation of (25m) without slipping of any wheel,whatis the required lenyth of the tic rod.

Answered: Image /qna-images/answer/1c27981e-185e-4a31-ae65-06395fae8ad6.jpg

dn an auto employing the Ackermann Steering gear, the sid Enks make (20) with the Vertical. The wheel base is (2.6m) nd the distance bet ween king pins is (1.6m). the auto is desired to turn about an radius average erotation of (25m) without slipping of any wheel , what - the required length of the tir

dn an auto employing the Ackermann Steering gear, the sid Enks make (20) with the Vertical. The wheel base is (2.6m) nd the distance bet ween king pins is (1.6m). the auto is desired to turn about an radius average erotation of (25m) without slipping of any wheel , what - the required length of the tir

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
Dynamics A 500 N force is applied to a roller with a massof 50 kg as shown. Assuming that the roller is auniform cylinder and there is no slipping,determine the angular velocity of the roller.
A band and block brake having 10 blocks, each of which subtends an angle of 14o at center, is applied todrum of effective diameter of 1 m. The brake drum and winding drum of crane mounted on the sameshaft weighs 20 kN and have combined radius of gyration of 300 mm. The two ends of the band areattached to the pin on opposite side of the fulcrum. If an effort of 300 N is applied at distance of 800mm from the fulcrum, find (i) Braking torque, (ii) the angular retardation of the brake, (iii) the timetaken by the system to come to rest from the rated speed of 400 rpm. Take coefficient of frictionbetween the drum and the block as 0.25.
Carry out the speed analysis of the following mechanism, obtaining the general expressions (for any position) for the angular velocity of the bar BD and the sliding speed of the collar P on the bar BD. The angular velocity of the bar AP is known. Assume that the position analysis has already been carried out. Also report the expressions for linear and angular velocity of collar P.
extension of spring when θ=90°. (m) angular velocity when θ=90° (rad/s)
Two shafts the axes of which intersect but are inclined to each other at 20 degreeconnected by means of a universal joint. At what position in the rotation cycle of thedrive shaft (i) velocity ratio will be maximum, minimum and unity (ii) the accelerationis maximum?
A shaft has three eccentrics of mass 1kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20 mm, 30 mm, and 20 mm and their angular positions are 120 degree apart. Find the amount of out-of-balance force and couple at 600 rpm. If the shaft is balances by adding two masses at a radius of 70 mm and at a distance of 100 mm from the central plane of the middle eccentrics, find the amount of masses and their angular positions. (Use graphical method for solution)
Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of gravity. Gear A has a radius of .8 ft and is experinceing a 10 ft-lb CW moment Gear B has a radius of 1.2 ft If gear A is initially moving at 60 rpm CW, determine how long it will take for gear B to be rotating at 300 rpm CCW
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
For a Davis steering gear, the gear's track arm is at a distance of 160 mm from the front main axle and the difference between their lengths is 100 mm. If the distance between steering pivots of the main axle is 2 m a) find the inclination of the track arms to the longitudinal axis of the vehicle b)determine the length of the chassis between the front and the rear wheels.
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0
In your job as a mechanical engineer you are designing aflywheel and clutch-plate system. DiskA is made of a lighter material than disk B, and the moment of inertia ofdisk A about the shaft is one-third that of disk B. The moment ofinertia of the shaft is negligible. With the clutch disconnected, A isbrought up to an angular speed v0; B is initially at rest. The acceleratingtorque is then removed from A, and A is coupled to B. (Ignorebearing friction.) The design specifications allow for a maximum of2400 J of thermal energy to be developed when the connection ismade. What can be the maximum value of the original kinetic energyof disk A so as not to exceedthe maximum allowed value of the thermalenergy?