Dons at C, ar 2"

Q: Daw the Free buly Dingram

A: Free body diagram of given figure

Q: d the answe

A: Convection Convection consists of 2 mechanisms Energy transfer due to random molecular motion…

Q: rs in an ass

A:

Q: 10 times larg solf hell is uC

A:

Q: ane area is

A:

Q: tion meets

A:

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: pot

A:

Q: on c is 0, what is th

A:

Q: eaga (w)=1 rade\s counter cloch

A:

Q: 2) In ed the number 2,1 is done

A: Given view:   isometric view  To sketch the isometric view

Q: C2 (ii) Explain the operating characteristics of wind mill.

A: NOTE : As per guideline ,we can only do 1 question at a time. so please upload the remaining…

Q: an angl ng in a w ing attacl is incline

A:

Q: Two inward flow to

A: 437 RPM

Q: Name: Coune

A: given:

Q: the Poisson's

A: Given; A square plate of dimension L×L Uniform pressure load p=250 MPa, on its edges as shown in…

Q: 5m nas Taz ?

A: Given Data: Length of the beam, L=5 m

Q: e of 400 N is a dentical bar of noro?

A: given:E=400N

Q: en expanded isothe nally compressed a to the init

A:

Q: placed by oil in the wate

A: Given Data : Water is replaced by oil in water pump

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: о ре cional area

A:

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: CHA

A: For solution refer below images.

Q: troid, ỹ on axis x'- x ' for the parts cross-sectic

A:

Q: of Appendix D as needed. spacec equal

A: we have to determine the distance where the two forces become equal

Q: heir origin at the centroi

A:

Q: A ce folla

A:

Q: is filled to height|

A: given:A=525in2h=67inmass m=56slug

Q: the power developed

A: Given: Under steady state:Specific enthalpy and velocity of steam at inlet and exit of a…

Q: ure till its vO orature is

A:

Q: al is the magni

A:

Q: long a 2' bar. bar falls head-on Buth An 8' on bars hav the same Find the stres ses ビ and A. maxi…

A: Given:-Bar A=8' longBar B=2' longSame E and ATo find:-Maximum dynamic stress

Q: (b) The total average (c) The total average

A:

Q: Wh at are, the re as shown in the JO

A:

Q: a = -ks?,

A: 2/6 (ANSWER)

Q: ω3 and ω4 = rad/s ?

A:

Q: nd the moghnitude

A: Given: Two force are equal R=153 Angle between one force and resultant is 30 degree To determine:…

Q: A 4 stroke 4 cylinder car engine of 4 L. What will be the swept volume of each engine?

A: Given:A 4 stroke four cylinder  has a swept volume of 4litre(L)Since nothing else is mentioned we…

Q: the different methods of the water tre

A: introduction: A boiler feed water treatment system could be a assortment of technologies that…

Q: The maximum radial load it can sustain

A: Given; The dynamic laod capacity of 6306 bearing Load=20kNThe maximum radial load?Rotation=650…

Q: rope is wrapE

A:

Q: Differentiate enery and force

A: energy is defined as the amount of work that can be performed by force and units of the energy is…

Q: f the desc oth of cut rations

A: Chip forming ;

Q: Pls answer the sub parts (ii), (iii) and (iv).

A: Consider the T-s diagram shown below for the given process.

Q: • What is: d cos(at +d), dt

A:

Q: ed vessel contains 3 k che vessel till the ga k done on or by the ga

A:

Q: D, the smallest pipe for

A: GIVEN- Re= 2300 Q= 1L/s TO FIND- Smallest pipe (D)

Q: 3m G3m F?m

A: Equilibrium of a section of truss is considered in method of section. Procedure in method of…

Q: The power output of

A: Given; Steam enters an adiabatic turbine operating at steady state with an;Enthalpy of,H=3251.0…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.