Draw the stress-strain diagram for a steel specimen (a ductile material) showing both the conventional and true stress-strain curves. Label all aspects of the diagram. Define the following regions in the above diagram: elastic behavior, yielding, strain hardening, and necking. What are the characteristic stress limits? Locate and define them on the curves.

Draw the stress-strain diagram for a steel specimen (a ductile material) showing both the conventional and true stress-strain curves. Label all aspects of the diagram. Define the following regions in the above diagram: elastic behavior, yielding, strain hardening, and necking. What are the characteristic stress limits? Locate and define them on the curves.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. In the nominal stress-strain diagram (Figure 1), write down the names and meanings of points 1, 2, 3, and 4.2. Explain how to find the 0.2% offset yield strength, and explain the% elongation and% reduction in cross-sectional area.3. After explaining the difference between the true stress/strain and the nominal stress/strain, show the true stress-strain diagram for the nominal stress-strain diagram (Figure 1) to correspond points 1, 2, 3, and 4.
During stress-strain test, the unit deformation at a stress of 35 MPa was observed to be 167 x 10^-6 m/m and at a stress of 140 MPa it was 667 x 10^-6. If the proportional limit was 200 MPa, what is the modulus of Elasticity (GPa)? What is the strain corresponding to a stress of 80 MPa?
For some metal alloy, a true stress 345 MPa (50040 psi) produces a plastic true strain of 0.02. How much will a specimen of this material elongate when a true stress of 418 MPa (60630 psi) is applied if the original length is 500 mm (19.69in) ? Assume a value of 0.22 for the strain- hardening exponent, n
Define plane stress and plane strain, making clear which, if any, of the stresses are zero in each case.
Can we determine the relationship between the average normal stress and average normal strain by performing the tension test?
Based on the stress-strain plots, which materials tested are stiff and which are tough? How can you tell the difference? * we tested (Steel HR250)and (Aluminium 5251)in this experiment
a)Comment onthe relative errorof the numbers obtainedgivenonehadno ideaof the actual condition. b)If you glue strain gages on a plate loaded up edgewise, take readings and thencompute the state of stress,which assumption should you use and why?
In the case of plane stress, how can the plane-strain analysis be used?
Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and (c) a circulartubecross section, and label the dimensions symbolically (e.g.,label the radius for the solid circular case). For each member, write out the definition of engineering stress in terms of the actual dimensions of the component. If therectangular member has dimensions of width and thicknessequal to 1 cm 0.3 cm, what would be the radius of a solidcircular member such that the stress is equal for an equaltensile load? If a tube has an outer radius equal to that ofthis same solid cylinder, what is the maximum inner radiussuch that the stress does not exceed 200% of the stress inthe solid cylinder?
Stress can be related to strain. Explain by using experimental methods?
Draw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking region
When a thin cylinder is subjected to an internal pressure p, the tangential stress should be the criterion for determining the cylinder wall thickness. Explain.