Plot the engineering stress-strain curve these data Determine the 0.2 percent offset yield stress for this steel in MPa Determine the tensile elastic modulus of this steel in GPa (Note that these data only gives the beginning part of the stress-strain curve)

Plot the engineering stress-strain curve these data Determine the 0.2 percent offset yield stress for this steel in MPa Determine the tensile elastic modulus of this steel in GPa (Note that these data only gives the beginning part of the stress-strain curve)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Related questions

Q: How does the carbon content in plane carbon steels affect the fracture toughness? Show this…

A: The fracture energy of a material is tested by using impact tests. The impact test measures the…

Q: 6. What is yield stress, how is it determined for metallic materials. Give the reason behind yield…

A: Yield stress is defined as the minimum stress at which a material will undergo strain without any…

Q: Find the Brinell hardness number of the material

A: To Find Brinell hardness number of the material

Q: How do you increase the hardness of components being made from 0.8% carbon steel? Explain the…

Q: A gauge # 10 HSLA steel for an automotive application has a Young’s modulus of 200 GPa, a yield…

A: Find the punch force required

Q: 2.) An S-five ninety alloy specimen nine hundred mm long will be subjected to eighty MPa tensile…

A: Solution; Given Data: L=900 mmσ=80 MPaT=815oCt=5000 hrs To Find: ∆L

Q: Is there relationship between hardness and tensile strength? What is the relationship in these two…

A: Hardness can be estimated substantially more promptly than can tensile strength, there is an…

Q: The rigid beam is supported by three 25-mm diameter A-36 steel rods. If the beam supports the force…

A: Find the force in each member.

Q: As the tempering temperature of a heat treated steel increases the associated values of Brinnell…

A: Tempering is a heat treatment technique applied to ferrous alloys, such as steel or cast iron, to…

Q: e) Compute the strain hardening exponent at the true tensile stress [take K = ) Quantify ductility…

A: The data is shown in two graphs below: the first depicts the whole stress-strain curve, while the…

Q: Please elaborate the following: Typical stress-strain characteristics of steel in simple tension and…

A: Characteristics of Stress Strain Mechanical Properties

Q: A batch of casted mild steel has a modulus of elasticity of 200 GPa and a yield strength of 250MPa.…

A: Modulus of resilience is the maximum amount of energy that can be stored in a material without…

Q: From the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is…

Q: Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and…

Q: Determine the material property of the materials from the following website. Material Property Data…

A: GIVEN = C1045 CARBON STEEL

Q: A 10 mm diameter Brinell hardness indenter produced an indentation 2.5 mm in diameter in a steel…

A: Brinell Hardness Number (HBN/BHN) is the numerical value given to the hardness of given material.

Q: Briefly explain the ASTM grain-size standard. Draw a stress-strain curve for a ductile metal and…

A: ASTM grain size standard: ASTM (American Society for Testing and Materials) grain size standard is…

Q: Q2: (A) A material has a yield stress of 300 MPa. What will the cross sectional area of the bar,…

A: Given Data: Yield Stress σyt=300 Mpa Force F=36000 N Cross sectional Area A=?

Q: a. What is the Brinell hardness number (HB) for 1020 Steel that has been annealed at 785 "C? (Check…

Q: A part made from hot-rolled AISI 1212 steel undergoes a certain amount of cold-work operation. If…

Q: A 10-mm-diameter Brinell hardness indenter produced an indentation of 1.52 mm in diameter in a steel…

A: BHN The Brinell hardness test is commonly used to determine the hardness of materials like metals…

Q: 11.4 mm (0.45 in.) in diameter is to be cold worked by drawing; the circular cross section will be…

Q: Suppose a 24 in. long round bar is to support a load of 400 lb. without any permanent deformation.…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Suppose that you are making preliminary design calculations for a deep submersible vehicle that is…

A: Given that, Radius of hemispherical shell, r=1.5 m,Internal pressure inside the shell, Pi=1×105…

Q: By using the Young's Modulus - Strength material selection chart in Figure Q11. Sketch the specific…

A: First we will mark the region where strength is greater than 30 MPa

Q: steel has zero mean stree of 320 Mpa ,mean stress of 200 Mpa ,tensil of 740 Mpa,yield stress of 1.5…

Q: A 1.23 cm diameter bar is subjected to a load of 2500 kg. Calculate the engineering stress on the…

A: Given Data, Mass applied on the bar M= 2500 kg Diameter of bar d=1.23 cm

Q: Determine the material property of the materials from the following website. Material Property Data…

A: The mild and hot-rolled steel ASTM A36 is the most widely utilised. It is appropriate for grinding,…

Q: The figure below shows the stress-strain behavior of a mild steel (the insert shows part of the same…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: What will be the maximum force that can be withstood by a rod

A: The tensile strength (tensile stress) of the aluminium alloy rod σt=140 MPa Cross sectional area of…

Q: For the stress states above determine the required yield strength of the material based on the…

Q: n application requires ultimate tensile strength and yield strength of a steel at 110 ksi and 91…

A: I. Can SAE 1040 steel be selected for this application? Yes, It can be selected. Because the…

Q: Task #7 The yield strength of mild steel with an average grain size of 0.05 mm is 20,000 psi. The…

A: Given Case 1 Average grain size = 0.05 mm Yield strength = 20000 psi Case 2 Grain size = 0.007 mm…

Q: ate tensile strengths and the same percentage elongation, yet they are not the same steels. What are…

A: given: Materials 605M36 and 655M31 have the same yield and ultimate tensile strengths and the same…

Q: A non-cold-worked cylindrical rod with an initial length of 800 mm and diameter of 15 mm is to be…

A: Given; The initial length of the rod, L = 800 mm The diameter of the rod, d = 15 mm The tensile…

Q: 6. How do you increase the hardness of components being made from 0.8% carbon steel? Explain the…

A: We can increase the hardness of low carbon steel by the carburizing process.

Q: In the flow curve for pure aluminum, the strength coefficient = 175 MPa and strain-hardening…

Q: (d) The yield strength values of pure aluminium (Al) and pure copper (Cu) are 25 MPa and 20 MPa,…

A: Solution: Given Data: σy,Al=25 MPaσy,Cu=20 MPaσy,AMM=200 MPaσy,CB=105 MPad=18.4 mm

Q: Determine the yield strength sy and the ultimate strength su of the A36 steel either from Materials…

A: To find: For A36 Steel Yield strength sy = ? Ultimate strength su = ?

Q: Estimate the linear relationship between the Ultimate Tensile Strength and HBN for the range of…

A: here take linear line of brass alloys from strength Vs BHN diagram. Now locate extreme point of…

Q: Describe the material behavior of Steel

A: Material behaviour of steel 1. Ductility: The ductility of steel can be changed by changing the…

Q: Briefly describe the metallographic procedure. Briefly explain the ASTM grain-size standard. Draw a…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Specify a copper alloy that requires at least 50% elongation and at least 300 MPa tensile strength.

A: The stress-strain curve for a copper alloy (Brass) is given as under:

Q: 5. () A 10-mm-diameter Brinell hardness indenter produced an indentation 2.50 mm in diameter in a…

Q: lasticity, el

A: solution of above question is below

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

46 69% i 12:28
Problem 6.4 - Read-only
Read Only - You can't save changes to this file.
PROBLEM 6.4
The following engineering stress-strain
data were obtained at the beginning of
a tensile test for a steel specimen.
(a) Plot the engineering stress-strain
curve these data
(b) Determine the 0.2 percent offset
yield stress for this steel in MPa
(c) Determine the tensile elastic
modulus of this steel in GPa
(Note that these data only gives
the beginning part of the
stress-strain curve)
PROBLEM 6.4
Engineering
Stress (MPa)
Engineering
Strain
(mm/mm)
15
0.0005
30
0.0010
40
0.0015
50
0.0020
60
0.0035
66
0.0040
70
0.0060
72
0.0080

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given Data

VIEW

What needs to be determined

Method

Calculation

Result

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
Find the total toughness energy for a metal that experiences both elastic and plastic deformations. The modulus of elasticity is 107.2 GPa, and elastic deformation terminates at a strain of 0.009. For plastic deformation, assume that the relationship between stress and strain is described by T = 1.66xKn, in which the values for K and n are 1453 MPa and 0.175, respectively. Furthermore, plastic deformation occurs between strain values of 0.009 and 0.67, at which point fracture occurs
The data below are for a thin steel wire suitable for use as a guitar string. Ultimate tensile stress: 1.8 x 109 Pa Young Modulus: 2.2 x 1011 Pa Cross-sectional area: 2.0 x 10-7 m2 In a tensile test, a specimen of the wire, of original length 1.5 m, is stretched until it breaks. Assuming the wire obeys Hooke’s law throughout, calculate the extension of the specimen immediately before breaking.
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the propotional limit, modulus of elasticity (i.e the slope of the initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percent reduction area. TENSILE-TEST DATA Load(kN) Elongation(mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
Consider the tensile stress-strain diagram below. If samples 1 and 2 are identical except that they were tested at different temperatures, which sample was tested at a lower temperature? Note: This question will be marked negatively so consider your answer carefully. A. Sample 1 B. Both were tested at the same temperature/ Alby is by die dieselfde temperatuur getoets C. Sample 2
A Copper specimen of circular cross-section is subjected to a tensile test. The data obtainedare:Length of Specimen = 329 mm;Diameter of Specimen = 39 mm;Load at Yield Point = 130 kN;Maximum Load = 219 kN;Load at fracture = 118kNDetermine the following:1) Find initial area of the test specimen2) Yield Stress3) Ultimate Stress4) Fracture stress5) Find the strain for 0.058mm elongation.6) Mark Yield stress, Ultimate stress and Fracture stress on a Stress-Strain diagram.
A material has the following properties, ultimate Sul = σul = 350mpa, the strain hardening exponent n=0.20. Determine the value for the strength coefficient K.
To manufacture a piston with a circular cross section, an alloy steel bar is required whose length is fixed and has a value of 35 cm and must withstand a compression load of 5.2 tons. For its design, a safety factor of 4/5 is suggested with respect to the yield stress. The shear modulus for that alloy is 80 GPa.To know the resistance of this steel alloy, a compression test was carried out on a specimen of the same material, from this test the data table of stress against engineering deformation shown was obtained. Image 1 1) Calculate the increase in the diameter of the bar when the load is applied2) Define the Poisson's ratio and calculate its value
Figure 6.23 shows the tensile engineering stress– strain curve in the elastic region for a gray cast iron. Determine (a) the tangent modulus at 25 MPa (3625 psi) and (b) the secant modulus taken to 35 MPa (5000 psi).
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mmdiameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) : a) Modulus of elasticityb) Yield strengthc) Toughnessd) Resiliencee) Shear modulusf) Bulk modulusg) Ductility as described bypercent change in length
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. Select one: The tensile yield strength Sy = 100 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 170 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 150 Mpa and the maximum strength Smax = 200 Mpa. The tensile yield strength Sy = 240 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 80 Mpa and the maximum strength Smax = 250 Mpa.