Draw/sketch the reinforcement details under moment only for the following reinforced concrete structure (in both longitudinal and cross sectional views as shown), given the moment diagram. Assume that in the tension side, 4#8 bars are needed and neglect steel bars required in the compression side. (Also explain your final sketch)

Draw/sketch the reinforcement details under moment only for the following reinforced concrete structure (in both longitudinal and cross sectional views as shown), given the moment diagram. Assume that in the tension side, 4#8 bars are needed and neglect steel bars required in the compression side. (Also explain your final sketch)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
Fill in the blanks: Determine the required tension steel area of the T beam with given properties below. Width of flange bf= 500 mm Width of web bw = 400mm Thickness of flange tf 140 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 30 MPa Yield stress of steel bar fy = 300 MPa Mu = 448 kN-m As = mm2 CS Scanned with CamScanner
Illustrate the single reinforced section with rectangular stress block.
H.W.11: Calculate the design bending strength for the doubly reinforced rectangular section shown below where A' (3025), A, (6025), f = 34.5 MPa and fy = 414 MPa. 3025 mm 450 mm 6025 mm 250 mm 50 mm 475 mm
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
A beam has an f'c = 5000 psi, fy = 60000 psi, reinforcement ratio = 0.0137. Which of the following is most likely true about the strain in the extreme tension steel? Use the tables posted to Canvas as needed (The ones in the back of the book). The strain is = 0.005
H.W.12: Calculate the design bending strength for the doubly reinforced rectangular section shown below where A,' = 2500 mm², A, = 8500 mm², f = 30 MPa and fy = 350 MPa. As As 250 50 500 11
Problem No. 3A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume Cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement O 0.00182 O 0.00201 O 0.00224 O 000391 O 0.00577
4. Analyze the beam shown below given fe' = 3500 psi and fy= 60,000 psi: (a) Use d = 22 in. (effective depth of tension reinforcement), assuming the compression steel yields at the ultimate stage, calculate the reinforcing ratio of flexural reinforcement. (b) Is the beam underreinforced or overreinforced? Show reasons to your answer. (c) Calculate the nominal flexural strength of the section: M,? (d) Determine the design capacity of the section: øMn.
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __ mm
Design a rectangular section for reinforced concrete beam knowing that the concrete compressive strength f'c = choose from 21 to 30 MPa and the steel yielding strength fy= choose from 460 MPa to 500 MPa. 1- Draw the shear force and bending moment diagrams. 2-Find the suitable dimensions for the beam. 3- Calculate the required steel reinforcement. Use diameter of 10 mm, 12 , 16 mm and/or 25 mm. mm, 4- Draw the final cross-section and the reinforcement layout. تعلیق أعجبني be 250 mm to 300 mm PL =45 kN WL=IS KN/m h= 600 mm to 700 mm 5 m WdL= Self-Weight (cross section)