During a start-up of flow loop F-10, a problem is found in which a turbine flowmeter that outputs 4 pulses per gallon (3.79 liters) is now required to have a pulse output of 1 pulse per 500 gallons (1892.71 liters). What is the new scaling factor needed in the totalizer for this change? 4 125 500 2,000

During a start-up of flow loop F-10, a problem is found in which a turbine flowmeter that outputs 4 pulses per gallon (3.79 liters) is now required to have a pulse output of 1 pulse per 500 gallons (1892.71 liters). What is the new scaling factor needed in the totalizer for this change? 4 125 500 2,000

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter42: Electronic Automatic Transmissions

Section: Chapter Questions

Problem 13RQ: A glitch appears in the waveform of a vehicle speed sensor. Which of the following is not a probable...

See similar textbooks

Similar questions

A glitch appears in the waveform of a vehicle speed sensor. Which of the following is not a probable cause of the problem? a. A loose connector b. A damaged wire c. A poorly mounted sensor d. A damaged magnet in the sensor
Draw the block diagram of a Displacement measurement system .Also identify the names of the functional elements used in the measurement system.
A CNC machine tool table is powered by a servomotor, ball screw, and optical encoder. The ball screw has a pitch = 7.5 mm and is connected to the motor shaft with a gear ratio of 12:1. The optical encoder is connected to the ball screw and generates 200 pulses/rev of the screw. The table must move a distance of 300 mm at a feed rate = 450 mm/min. (a) Determine the pulse count received by the control system to verify that the table has moved exactly 300 mm. Also, what are (b) the pulse rate and (c) motor speed that corresponds to the specified feed rate?
18- A)Define the following (iii) Dynamic Errors (iv) Controlled variable (v) Use of PI Controller
If the load disturbances in flow control systems are rapid and enought to cause the system to oscillate, an integral control may be added to provide immediate response. a. Trueb. False
A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
Disadvantages, advantages and differences between detrended fluctuation analysis (DFA) and Multifractal Detrended Fluctuation Analysis (MF-DFA).
A 12-bit digital-to-analog converter has an output range of 0 to 10 V. Estimate the analog voltage output if the input is simple binary and has the decimal value of 45.
Referring to Figure 1, Explain the sensor mechanism in terms of block diagram. Indicate all basic functional elements. (i.e Primary Sensing Element, Signal Conditioning Element, Signal Processing Element, Data Presentation Element etc) Can you suggest how to increase sensitivity of this sensor? (See Figure 1) attached image Figure 1 Float-Operated Fuel Level Gauge used in automobiles
If output to the valve (M) = Gain * Error + Gain *(t /TC) S (error), what is the output after two time interval? The initial values are Gain = 0.4; SP = 60; PV = 50; and t = TC.
"the axis of this feature should be coaxial within .006 with the datum axis, as measured RFS with the datum RFS". also in feature control frame.
Describe the typical procedure for adjusting a TP sensor.