If the load disturbances in flow control systems are rapid and enought to cause the system to oscillate, an integral control may be added to provide immediate response. a. True b. False

Q: throttle actuator velocity v intake pipe throttle angle (aTH) slope (a) For vehicle speed control…

A: given; ⇒moving velocity =v⇒car moving with acceleration =a  ⇒lets take weight of body =w⇒normal…

Q: Direction control valves is an example of which element of closed loop system? O a. Correction…

A: Direction control valves are one of the most fundamental part of hydraulic system. it controls the…

Q: Reprogramming is possible in CNC (Computer numerical control) systems. Select one: True False

A: Reprogramming is not possible on CNC systems because once it is activated it can’t be undo

Q: Which of the following is correct for a open loop system ?

A: The main problem with the open loop control system is that, it do not monitor or check the condition…

Q: C. Compare and Discuss the different speed control cases and mention the limitations for the Closed…

A: Let's compare the different speed control cases first of all speed control of of DC motor  Flux…

Q: The control signal from the controller reduces the error. Select one: O True O False

A: The controller is to produce a signal that is suitable as input to the controlled plant or process.…

Q: Circuit Problem and Description: Using the given components, design two pneumatic circuit which will…

A: Given : 2 Circuit description To find : Circuit diagram

Q: ») Explain the basic components of closed loop system shown in figure (a) Error Detector Actuating…

A: A closed-loop control system can be defined as, a system that has a feedback loop (or) a control…

Q: The ability of the instrument to give same output for same input when the conditions are different…

A: When the conditions are same, for same input, the ability of instrument to give same output is…

Q: In which control system, output from the system has no effect on command signal? O a. Feedback less…

A: In Feedback less system, output from the system does not sent back to the controller. Therefore,…

Q: A major disadvantage of on/off control is that it cannot work for applications requiring very small…

A: On-off controller (also called two-step controller) turns on or off the machine based on the error…

Q: For an on/off pressure control system, which of the following best describes the function of the…

A: Pressure control systems are designed to control the magnitude of force produced by a fluid inside…

Q: 1. Consider two identical independent units with failure rate of 0.01 hr1. Assume the mission time…

A:

Q: Represent in block diagram form, the control system used in automatic control of speed of a steam…

A:

Q: Which of the following is correct? Final value theorem is not applicable for the sys Select the…

A: As time approaches infinity, the final value theorem (FVT) is one of the theorems used to link…

Q: When selecting a Data Acquisition module for thermocouple measurement, what is an important…

A: Correct answer is  ⇒cold junction compensation hence first option is correct.   Explanation⇒…

Q: is an interconnection of components forming a system configuration that will provide a desired…

A:

Q: Meter-out of pneumatic circuits utilizes check valve in only single direction. Select one: O True O…

A: We have to determine true/false

Q: i) Suggest two sensing elements to measure Flow parameter. ii) Identify the control strategy used in…

A:

Q: In the following closed-loop control system, identify the dynamic system, the actuator, the…

A: Given: To find: Dynamic system, actuator, controlled variable, manipulated variable and control…

Q: Fill in the blanks with the most convenient answer: The main problem with very sensitive to…

A: In mechatronics systems, the input may or may not depend on output. Based on this system can be…

Q: i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction Element

A: Given: To identify: (i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction…

Q: (b) Identify the following elements of the given closed loop control system. (1) Process Element…

A: The closed loop system is given by -

Q: (Can someone help me with this just need a P&ID solution meeting the requirements and explanation.…

A: A P&ID gives a point by point graphical portrayal of the genuine interaction framework that…

Q: 3. You are assisting a company that is installing new compressors and updating their pneumatic…

A: Compressors selection

Q: Which type of control system is used in the given block diagram? Write the definition.

A: The Control system used in this diagram is open-loop control system.

Q: Explain abou the Identification of the variables to monitor during Planning an Instrumentation…

A: The planning program utilizing instrumentation is really same to some other plan endeavors starting…

Q: true or false need before 7:45 pm pleaseeee neeed it 1.Mass component that do not vary as it…

A:

Q: Which of the following is correct for a open loop system ? O a. No comparison element O b. Automatic…

A: In an open loop system,

Q: In an industry, the water in a boiler tank needs to be kept at constant pressure, water to the tank…

A:

Q: There are different states in a 4-bit Johnson counter

A: There are 8 different states in a 4-bit Johnson's counter.  Option B is correct.

Q: Which may not be an input of a control system? * actuating signal; setpoint; controlled variable;…

A:

Q: List the three modes of industrial process control and specify the effect of each when a process…

A: In any industrial plant, various types of operations proceed. A process is the conversion of raw…

Q: Human-aided control system for controlling a fluid level in a tank is shown in Figure Q2a. Here H…

A: Draw a block diagram for human aided control system for controlling the fluid level in the tank.

Q: What is the purpose of Flow Control? O Keep the buffer in the transmitter from going empty Prevent…

A: Option (a) is correct.

Q: ect response:

A: Given data Vector A= -25mi+45mj Vector along x axis = I+0j Required Angle between  Vector Aand…

Q: (b) A special sprinkler system is comprised of three identical humidity sensors, a digital…

A: Given Data⇒Reliability of sensor controller and pump areRs=0.916,Rc=0.965,Rp=0.983Problem…

Q: What is an error? O a. The difference between true value and measured value O b. The difference…

A: The correct option is option (A) The difference between true value and the measured value.

Q: VIbration subject. State 4 methods that can be used to control vibration.

A: As Vibration is the complete measurement of acceleration of vibration which unit is m2/s . Here we…

Q: There are many types of traffic control system for the lift system. Give a short account on the…

A: Write a short account on the following three control systems.  (1) Down collective control.(2)…

Q: Sensitiveness of a governor is defined as the ratio of the

A: Sensitivity of governor is inversely proportional to stability of a governor.

Q: Draw the circuit diagram for the following system. The diagram must be neat, legible, and…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.