E 2m + 2m 2m 1.5m 2m 2 kN E 2 kN 2 kN 1) a) Determine the force in members CE, BD, and CD and state if these members are in tension or compression. SCE= _kN SBD= kN ScD= _kN Tension or Compression Tension or Compression Tension or Compression 1) b) The pins on the truss's supports at A and G each have a diameter of 2cm. If these pins are subjected to (t.) - MPa (*) double shear at support G, ave= (*) single shear at support A, ave= _MPa determine the average shear stress in each pin. c) If the allowable stress of truss members is o= 60 MPa, what is the necessary diamete for bar FG to keep the truss system is safe? 1) (.)= mm

E 2m + 2m 2m 1.5m 2m 2 kN E 2 kN 2 kN 1) a) Determine the force in members CE, BD, and CD and state if these members are in tension or compression. SCE= _kN SBD= kN ScD= _kN Tension or Compression Tension or Compression Tension or Compression 1) b) The pins on the truss's supports at A and G each have a diameter of 2cm. If these pins are subjected to (t.) - MPa () double shear at support G, ave= () single shear at support A, ave= _MPa determine the average shear stress in each pin. c) If the allowable stress of truss members is o= 60 MPa, what is the necessary diamete for bar FG to keep the truss system is safe? 1) (.)= mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5 - note: ignore weight of the bar.A) ( - 6/7)T(CB) + A(y)=0 (A=reaction force at A, A(x), A(y), A(z) are components of force A)B) (2/7)T(CB)+A(x)=392 (A=reaction force at A, A(x), A(y), A(z) are components of force A)C) A(x)=2A(y) (A=reaction force at A, A(x), A(y), A(z) are components of force A)D) A(x)=5A(z) (A=reaction force at A,A(x), A(y), A(z) are components of force A)
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
Determine the horizontal displacement of joint C. The length, L, of trusses AC, BC is 1,300 mm. The applied force at joint C, is 5.0 kN. The cross-sectional area of both trusses, A, is 360 mm2. The elastic modulus of truss AC, E1, is 135 GPa. The elastic modulus of truss BC, E2, is 150 GPa.
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
Solve the truss structure using the joint's method, when m = 100 kg.
1. This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.9m wide and 3.6m high. If the force at the end of the arm is F = 170.0N, what is the force in member 2? Use a positive number if it is in tension and a negative number if it is in compression. 2. This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.2m wide and 3.0m high. If the force at the end of the arm is F = 150.0N, what is the force in member 9? Use a positive number if it is in tension and a negative number if it is in compression.
9-8kN stress/force on the AB rope holding the base station shown below There are. In order for the net force at point A of this base station to be downward What is the stress/force that should be on the AC rope? A) 5556 N C) 7356 N B) 8200 N D) 3648 N E) 1228 N
A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 20 in. The generator output is 40 Hp, 3600 rpm and 90% efficiency. If there are 10 bolts, determine the force acting on each bolt in kN.
The given plane truss structure below is (where truss member BD is a single member and should not be considered as 2 members) A. Statically determinate B. Statically indeterminate with redundant truss members C. Statically indeterminate with deficient truss members D. Can’t be determined
Note: kindly give me both answers.. A transmission cable 300 m long, weighs 600 kg. The tensions at the ends of the cable are400 kg and 450 kg. Find the distance of its lowest point to the ground. A. 145 m B. 150 m C. 153 m D. 148 m Answer is 150 m.. Show me the work The tip to tail addition of vector is also referred to as A. Parallelogram law B. Triangle law C. Trigonometry D. Square rule
The semi circular gate shown in the figure is hinged at B. Determie the force F Required to hold the gate in position? 5088.5 lbs
other given: T(sub B) = 80.11 T = 5.67 kN-m