i need the answer quickly In the differential gear ofa car shown in Fig. 11.30,the number of teeth on thepinion A on the propellershaft is 18 whereas the crown gear B has 90teeth.If the propeller shaft rotates at 1200 rpm and thewheel attached to the shatt S.has a specadof 255rpm, while the vehicle lakes a turn determinethe speed of the wheel atiached to the shaft S,

Answered: Image /qna-images/answer/e40aa397-f673-4620-881f-d39ce52c1357.jpg

Answered: e shafi S, his a spee

Engineering

Mechanical Engineering

e shafi S, his a spee

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
The max speed for the servo shown is 130RPM when connected to 6V. Assume that the gearbox on your servo is able to output a torque of 1.5 kg-cm while turning at this speed. Using the number of teeth on each gearprovided in the table, determine the torque and rotational speed of the output shaft on the DC motor. HINT: Work backwards from the output shaft and use the equations developed in class that relate the number of teeth to the torque. When working back from the output shaft to gear 7/6, realize that the “torque” transmitted by gear 7 is the SAME as the torque transmitted by gear 6 since they are joined. Then, relate the torque of gear 6 to gear 5 based on their numbers of teeth. Since gears 5 and 4 are actually one piece, the torque in 4 and 5 will be the same (as was the case for gears 6 and 7). Repeat for the other gears, working your way all the way back to the DC motor.
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
A chain with speed of 900 fpm has driving sprocket turns at 1000 rpm. If the pitch of chain is 3/4-in, find the number of teeth of driving sprocket. (Ans. 14 teeth)
In a gear power transmission situation, the torque apppied on one gear is always created by: ____, no matter whay types of gears employed. Normal Force Tangential Force Radial Force Axial Force
I n a reverted gear train, as shown in Fig. Q2, two shafts A and B are in the same straight line andare geared together through an intermediate parallel shaft C. The gears connecting the shafts Aand C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm.The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio ateach reduction is same. Find suitable number of teeth for all gears. The number of teeth of eachgear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance ofshaft C from A and B
A roller chain and sprocket is to drive vertical centrifugal discharge bucket elevator with a center distance of 70.82 inches. The pitch of chain connecting sprockets is 1.75”. The driving sprocket is rotating at 217 rpm and has 11 teeth while the driven sprocket is rotating at 38 rpm. Determine (a) the number of teeth of driven sprocket and (b) the chain length in pitches, and (c) the chain length in inches.
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. Theaddendum length is 5 mm and the module is 5.5 mm. If smaller wheel is the driver androtates at 1500 r.p.m. find the velocity of sliding at the point of engagement and at thepoint of disengagement.
mechanical principles Determine the velocity ratio for compound gear systems and the holdingtorque required to securely mount a gearbox.
A gear box has an input speed of 1500 rev/min clockwise and an output speed of 300 rev/min anticlockwise. The input power is 20kW and the efficiency is 70%. Determine the followings. a). The velocity ratio(or geo ratio) b). The input torque c). The output power d). The output torque e). The holding torque
Determine the horsepower of a 6 cylinder 4 stroke continental engine having a bore equal to 3.875 in stroke of 4 in, and rpm of 2700 if it has a bmep of 150 lb/sq. in.