E7.4 Use the differential equation approach to find i(f) for t> 0 in Fig. E7.4.3 k2k()6 mH6VFigure E7.4K0112 V2k0ANSWER:i()-2+ 6*-45×10mA.

Use differential circuit analysis to calculate i(t) fro t>0. We have to analyse this circuit at…

Answered: E7.4 Use the differential equation…

Engineering

Electrical Engineering

E7.4 Use the differential equation approach to find ((7) for t> 0 in Fig. E7.4. 3k0 2k0 6mH Figure E7.4 KO 12 V 2k0

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Related questions

Q: EXAMPLE: Given a bridge rectifier has an AC source V=100V at 50Hz, and R-L load with R=10ohm, L=10mH…

A: given that Vm=100VR=10ΩL=10mH In case of diode bridge rectifier average output voltage…

Q: Л Ч -5 i(t) mA 10 Sinusoidal 5 10 15 1 (us)

Q: An averaging amplifier have five inputs with RF = 30 kohms, what should be the value of each input…

A: When all of the input resistors are equivalent, the summing amplifier is termed an averaging…

Q: In the circuit of figure below, if Vab= 440210° V, Vbc = 4402 - 110° V, Vbc = 4402130° V, find the…

A: Given: Vab=440∠10°Vbc=440∠-110°Vca=440∠130°

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional…

A: Inductive element consume reactive power but Capacitive elements deliver reactive power into the…

Q: Find the equivalent G(s) = C(s)/R(s) for the system shown below. R(s) C(s) 20 10 s+12 10 Find the…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 3. A parallel plate capacitor made up of two plates each with area A separated by distance d is…

Q: What is the cut-off frequency of the circuit below if R1 = 3645.24 Ω, R2 = 4039.54 Ω, R3 = 94.63 Ω,…

Q: .Design equation F(A,B,C,D)=E(1,2,3,6,8,10,12,13,15) using a 4x1 Mux?

A: Follow the Boolean laws provided Compare the obtained F with standard multiplexer notations and…

Q: Q3. An ac source in series with an impedance of (0.5 + j10) is connected to a transmission line…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: 4- The axial ration of a vertical antenna is AR=1. 5- The elevation plane of Omani-directional…

Q: A constant-gain multiplier has three stages and a total gain of 22,200. For all three feedback…

A: Given: Gain is 22,200 The value of the feedback resistor is 470 kohm The input resistance is 33 kohm

Q: Q³: From the circuit, find the following:- 1- Vc. 2- Vout at 12 volt. 3- Vour at -12 volt. 4- Draw…

A: Brief description: In the above given question they want to know the value of output and the…

Q: A capacitor made of 130 plates in parallel is separated by a 0.0297 m thick of insulator with a…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

A: As per the guidelines of Bartleby we supposed to answer first three subpart only for solution of…

Q: The poles of the system G(s) = (s + 2)/ (2s+8) is a. -2 b. 4 C. -8 d. -4

A: Given: System transfer function, Gs=s+22s+8

Q: Design a counter with T flip-flops that goes through the following binary repeated sequence: 0, 1,…

Q: E7.3 In the circuit shown in Fig. E7.3, the switch opens at r=0. Find i, (f) for r> 0.

Q: *15.31 Consider the phase-shift oscillator in Figure P15.30. (a) Assume the first re- sistor that is…

A: It is given that: R=25kΩC=0.001μF15≤RV≤30kΩ

Q: Given a certain common-source JFET amplifier in the laboratory, RD = 1 KΩ, RS = 560 Ω, VDD = 10 V…

A: Given common-source JFET amplifier RD = 1 KΩ, RS = 560 Ω, VDD = 10 V and gm = 4500 uS. Source…

Q: Use Simulink, you can set the symbol rate as 1 kHz. a) Plot the spectrums of the BFSK, 4FSK, 8FSK,…

A: To Plot the spectrums of the BFSK, 4FSK, 8FSK, 16FSK system

Q: The time constant RC has a unit of

A: In this question, We need to choose the correct options What is unit of the time constant RC?

Q: 2. In what conditions will the thyristor continue conducting? How to turn off the thyristor?

A: Condition in which thyristor will continue conducting : The main condition for a thyristor to be…

Q: IT Vs (rms) Load 2 12 kW 0.8 KVAR (capacitor) Load 1 2 kVA 0.707 (pf lagging) Figure 2 Load 3 20 kW…

Q: (b) Figure A1 shows a diagram of the measured &" of ice at different frequencies as a function of…

A: To show a diagram and temperature dependence is consistent with τ=τ0expT0TLet The Molecular model of…

Q: 1. Briefly explain how boundary scan testing can check PCB traces.

A: As per the Bartleby guidelines “Since you have asked multiple question, we will solve the first…

Q: In the given circuit below, which terminals should a voltmeter be connected to get the following :…

A: this is a bridge circuit diagram for measurement of output voltage for the output dc voltage we…

Q: Determine the phasor currents I, and I, in the circuit of Fig. 13.13. 5Ω j2 Ω 100/60° V j6 Ω -j4 Ω Μ…

A: Here we discuss about the circuit concepts using mutual coupled circuits.

Q: Calculate the steady-state errors for Types 0, 1 and 2 if the ramp input is applied to the system…

A: In this question we need to find a steady-state errors for Types 0, 1 and 2 if the ramp input is…

Q: The figure shows the popular dish antenna that receives digital TV signals from a satellite. The…

A: Given data, radius(r) = 16.3cm = 0.163mIntensity(I) = 7.40×10-14W/m2

Q: 53 1.9.3 Obtain the state-space model of the single-input- single-output network system of Figure…

A: State space model: It is a mathematical model for representing the physical system. The physical…

Q: The armature of a 4-pole, 130 slots shunt generator is lap wound with four conductors per slot. The…

A: From the question, it is given that Poles (P)=4 Lap wound=4 Flux ϕ=80 mWb Armature resistance…

Q: Using Mesh analysis, find the power consumed by each resistor and the voltages at each resistor. 292…

A: According to kirchoff's voltage law, the The net voltage in the loop should be zero. Supply voltage…

Q: 4 A capacitor has 0.035 * 0.035 m parallel plates. The distance between the plates is 0.092 m in…

Q: A balanced Y-Y four-wire system has phase voltages ??? = 120∠0° V, ??? = 120∠ − 120° V, ??? =…

Q: Sketch and explain the output for the circuit of given parameters. The generator signal is a sine…

A: In this question, We need to Sketch the output voltage waveform Using Third Diode Approximation?…

Q: Using mesh analysis, find io in the circuit below

A: In this question we will ise mesh analysis and find unknown current i0....

Q: For a given inverter with 1.2 pF load, the measured propagation delay times tPLH and tPHL are 9 ns…

A: In a ring oscillator odd number of inverters are connected in series with the positive feedback .…

Q: Solve for the total current in the circuit with components of 200 Ohms, 100 Ohms and 1k Ohms…

Q: Please answer all subparts for like either dislike is ready..Please sir

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A) Let x[n]=d[n]+[n-1]. Find the D.F.T of the signal g[n]=x[2n] B) Determine the I.D.F.T of the…

A: As per the guidelines of bartleyby I need to answer first question only so kindly repost other…

Q: A carrier signal given by 10 cos 2m x 10°t volt is FM modulated by single tone Hz message 4 cos 2 x…

A: It is given that: ct=10 cos2π×108t Vm(t)=4 cos2π×103t Vkf=1000 Hz/V

Q: Describe the behaviour of a p-n junction under forward and reverse biasing in terms of semiconductor…

A: P-N Junction- A P-N junction is an interface or a boundary between two semiconductor material types,…

Q: Find the equivalent resistance for the circuit in the figure below. R R R www w R R Vemf +

A: given here a electrical network and asked to determine the equivalent resistance of the circuit.

Q: Q4. The open-circuit and short-circuit test readings for a three-phase, Y-connected, 1 MVA, 2 kV,…

A: Given data, Voltage V=2000Volts

Q: Compute for the DC voltage (in V) of a 5V 15 kHz pulse train. The said pulse train has a duty cycle…

Q: Derive the formula for the energy stored in a capacitor.

A: Note : According to guidelines of the company if the questions are of different then we supposed…

Q: A signal was represented using Bipolar RZ with a bandwidth of 40 kHz, then the bandwidth will be…

A: The given bandwidth is 40 Hz.

Q: 4- The axial ration of a vertical antenna is AR=1. 5- The elevation plane of Omani-directional…

Q: What is the VDS of the circuit shown below? Where Ip(on) = 4 mA at VDS = 10 V, VGS(th) = 4 V and gm…

A: The required parameters can be calculated by using the DC analysis of MOSFET amplifier.

Concept explainers

Sinusoids And Phasors

Sinusoids are defined as the mathematical waveforms that are used to describe the nature of periodic oscillations.

Circuit Theory

Electric circuits are a network that comprises of a closed-loop, which helps in providing a return path for the current through a switch. When the switch is activated, the load operates, and the current accepts a path to finish the circuit at a low potential level from the opposing high potential level. Electric circuits theory is a linear analysis that helps in establishing a linear relation of voltage and current for R (resistance), L (inductance), and C (capacitance).

Question

E7.4 Use the differential equation approach to find i(f) for t> 0 in Fig. E7.4.
3 k
2k()
6 mH
6V
Figure E7.4
K01
12 V
2k0
ANSWER:
i()-2+ 6*
-45×10
mA.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compare the performances of the first order system, the overdamped, underdamped and critically damped second order system.
) Explain, with reasons, whether the LTIC systems described by the following equations are (i) stable orunstable in the BIBO sense; (ii) asymptotically stable, unstable, or marginally stable. Assume that the systemsare controllable and observable.a. (D2 + 8D + 12)y(t) = (D − 1)x(t)b. D(D2 + 3D + 2)y(t) = (D + 5)x(t)c. D2(D2 + 2)y(t) = x(t)d. (D + 1)(D2 − 6D + 5)y(t) = (3D + 1)x(t)
The system whose characteristic equation is given as s3 + 2s2 + Ks + 20 = 0 is asymptotically stable for which K values
A) Reduce the block diagram. B) G1(s)= 2/s, G2(s)= 1/4s+2, G3(s)=4, H(s)=0.5 According to these; find the time constant, natural frequency, damping rate, and dynamic behavior. C)G1(s)= 2/s, G2(s)= 1/4s+2, G3(s)=4, H(s)=0.5 Find the poles, zeros, and reverse Laplace of the system. Is it stable or not?
The mathematical models of some continuous time systems are given above. x(t) is the input signal of the system, and y(t) is the output signal of the system. Which of the following systems is linear and which is nonlinear? For linear systems, write "linear" in the space next to the option. For non-linear systems, write "non-linear" in the space next to the option.
For the circuit below with the switch closed and then opening at t=0, and R1= 9Ω, R2= 4Ω, L = 9H, C=3F, vg = 7V, calculate the initial conditions. For t > 0, develop the differential equation for the solution using mesh analysis.
For the circuit below with the switch closed and then opening at t=0, and R1= 3Ω, R2= 7Ω, C = 0.2H, ig = 8A, vs = 2v, calculate the initial condition. Develop the differential equation for the solution for t > 0. Calculate the current ia(t) for all times.
A)Perform the N=5 point circular convolution of x and h using DFT. B)Perform the N=5 point circular convolution of x and h in time-domain.
Find f(t) if F(s)=(2s3+8s2+2s−4)(s2+5s+4).
The RLC network below:a) Provide the second order differential equation describing this circuit b) Compute the undamped natural frequency of the circuit and the damping ratio.c) What type of response does i(t) exhibit for t > 0 ? Explain why.
1) In the circuit shown in Fig. 2, the switch is moved in accordance with the arrow at t = 0, having been in the top position for a long time. Solve for the current i(t), for t > 0 using the Laplacetransform.2) Find a state equation (x_ = Ax + Bu) to describe the network shown in Fig.3
If ? = 50Ω, L = 1.5H, what value of C will cause a sourceless series RLC circuit to be a) overdamped ?, b) critically damped ?, c) underdamped?