Each paddle wheel of a steamer have a mass of 1600 kg and a radius of gyration of 1.2 m. The steamer turns to port in a circle of 160 m radius at 24 km / h, the speed of the paddles being 90 r.p.m. Find the magnitude and effect of the gyroscopic couple acting on the steamer. [Ans. 905.6 N-m]

Each paddle wheel of a steamer have a mass of 1600 kg and a radius of gyration of 1.2 m. The steamer turns to port in a circle of 160 m radius at 24 km / h, the speed of the paddles being 90 r.p.m. Find the magnitude and effect of the gyroscopic couple acting on the steamer. [Ans. 905.6 N-m]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An object is formed by attaching a uniform, thin rod with a mass of mr = 6.86 kg and length L = 5.76 m to a uniform sphere with mass ms = 34.3 kg and radius R = 1.44 m. Note ms = 5mr and L = 4R. 1) What is the moment of inertia of the object about an axis at the left end of the rod? kg-m2 2) If the object is fixed at the left end of the rod, what is the angular acceleration if a force F = 463 N is exerted perpendicular to the rod at the center of the rod? rad/s2
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum. The mass of the drum is md = 100kg and the radius is r = 0.5 m. The radius of gyration of the drum about point O is ko=0.3 m. The mass of the block is mb= 20kg. The block is released from rest. The acceleration due to gravity g=9.81 m/s2 . (2) ) If the mass moment of inertia of the drum about point O is IO, and the angular acceleration of the drum is α, select the correct moment equation of the whole drum-block system about the point O._____________ A. mbgr=rmb(rα) B. 0 C. mbgr=Ioα +rmb(rα) D. mbgr=Ioα
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
A, B, C and D are the four masses carried by a shaft in this order. Radii of rotation of the masses are 20cm, 25 cm, 10 cm and 15 cm respectively. The masses of B, C and D are 3 kg, 5 kg and 4 kg respectively.The planes containing B and C are 25 cm apart. Angle between B and C is 90o and between B and D is220o measured in anticlockwise direction. For complete dynamic balance, find (i) The mass and angularposition of A, (ii) The position of planes A and D.
An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km per hour. The rotary engine and the propeller of the plane has a mass of 400 kg with a radius of gyration of 300 mm. The engine runs at 2400 r.p.m. clockwise, when viewed from the rear. Find the gyroscopic couple on the aircraft and state its effect on it. What will be the effect, if the aeroplane turns to its right instead of to the left ?
The turning moment diagram for a petrol engine is drawn to the following scales: turning moment 1 mm to 2·5 Nm; crank angle, 1 mm to 1°. The fluctuations of energy between the crank positions for minimum and maximum speeds corresponds to an area of 600 mm² of the turning moment diagram. The flywheel is made from cast iron, of density 7·2 tonnes/m3. Determine: (a) The greatest fluctuation of energy (b) The mass of the flywheel required to prevent the a fluctuation of speed greater than ± 0·5% from the mean speed of 1600 rev/min if the radius of gyration is 120 mm. (c) The dimensions of the flywheel (diameter and thickness) (d) Describe the possible consequences to the system if the flywheel was not used to limit the fluctuation of speed.
An engine flywheel has a mass of 6.5 tones and the radius of gyration is 2 m. If the maximum and minimum speeds are 120 r. p. m. and 118 r. p. m. respectively, find maximum fluctuation of energy.
A flywheel of mass 0.9 ton is fitted to a multi cylinder engine, which runs at a mean speed of 380 r.p.m. If the speed varies from 9 % above the mean to 6 % below it and the fluctuation energy is 1100 kN-cm, find (i) mass moment of inertia of the wheel and (ii) radius of Gyration.
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
Find the magnitude and position of the balancing mass at a radius of 13cm by using the analytical method. Three masses m1, m2, m3, are attached to a shaft and revolve in the same plane. The masses are 12kg, 10kg, and 15kg respectively and their radii of rotations are 5cm, 6cm, 7cm respectively. The angular position of the masses m2, m3 are 45° and 145° from the mass m1.
The crankshaft of a vertical engine, stroke 250 mm, rotates at 300 rpm. The reciprocating parts have a mass of 100 kg. The connecting rod has a mass of 120 kg, it is 450 mm long, the C.G is 300 mm from the gudgeon pin axis and the radius of gyration about that axis is 363 mm. When the crank is 30o from the TDC position and moving downwards, find:-The total kinematic energy of the connecting rod