End A of the bar AB in (Figure 1) rests on a frictionless horizontal surface, and end B is hinged. A horizontal force F of magnitude 290 N is exerted on end A. Ignore the weight of the bar. Part A What is the horizontal component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. ? F = Value Units Part B Figure < 1 of 1> What is the vertical component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. В HA ? 5.00 m F, = Value Units 4.00 m A

End A of the bar AB in (Figure 1) rests on a frictionless horizontal surface, and end B is hinged. A horizontal force F of magnitude 290 N is exerted on end A. Ignore the weight of the bar. Part A What is the horizontal component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. ? F = Value Units Part B Figure < 1 of 1> What is the vertical component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. В HA ? 5.00 m F, = Value Units 4.00 m A

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
A stepladder of negligible weight is constructed as shown in Figure P12.40, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P12.40 Problems 40 and 41.
A 15.0-in uniform ladder weighing 500 N rests against frictionless wall. The ladder makes a 60.0 angle ESI with the horizontal, (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when an 800-N firelighter has climbed 4.00 m along the ladder from the bottom, (b) If the ladder is just on the verge of slipping when the firefighter is 9.00 m from the bottom, what is the coefficient of static friction between ladder and ground?
Ruby, with mass 55.0 kg, is trying to reach a box on a high shelf by standing on her tiptoes. In this position, half her weight is supported by the normal force exerted by the floor on the toes of each foot as shown in Figure P14.75A. This situation can be modeled mechanically by representing the force on Rubys Achilles tendon with FA and the force on her tibia as FT as shown in Figure P14.75B. What is the value of the angle and the magnitudes of the forces FA and FT? FIGURE P14.75
a horizontal rod (m=5.2 kg) is hinged to a wall at the left end and three forces are acting on the rod as shown in the figure: the force of gravity (mg), a tension force (T), and the force exerted by the hinge (broken into components Fx and Fy) If theta = 35 degrees, what must T be equal to in order to keep the rod static?
A uniform beam 4.2 m long and weighing 2200 N carries a 3700 N weight 1.50 m from the far end, as shown in the figure below. It is supported horizontally by a hinge at the wall and a metal wire at the far end. 1) How strong does the wire have to be? That is, what is the minimum tension it must be able to support without breaking? Express your answer in newtons. 2) What are the horizontal component of the force that the hinge exerts on the beam? Express your answer in newtons. 3) What are the vertical component of the force that the hinge exerts on the beam? Express your answer in newtons.
A sign is supported by a uniform horizontal boom of length 3.10 m and weight 72.0 N. A cable, inclined at an angle of 16 °with the boom, is attached at a distance of 2.71 m from the hinge at the wall. The weight of the sign is 108.0 N. What is the tension in the cable and what are the horizontal and vertical forces Fx and Fy exerted on the boom by the hinge? Comment on the magnitude of Fy. T= In N Fx= in N Fy= in N The magnitude of Fy is select (small or large) compared to that of Fx and T.
The figure shows three boards clamped together. The center board weighs 93.5 N, and the coefficient of static friction between the boards is 0.490. What is the minimum magnitude of the horizontal compression forces (in N) acting on either side of the center board so it does not slip?
A wooden plank with a mass of 50.968 kg is supprted by two cable at its ends. At what location should a box of mass 20.387 kg be placed for one cable to exert a force of 125 N more than the other cable? Note: the location is the distance from each cable please show full solution, figure and fbd.