Equivalent circuit parameters R1 = 1ohm, X1 = 2ohm R2 = 0.0035 ohm X2 = 0.0045ohm Xm = 1100ohm Rfe = 6400ohm. The primary voltage of the transformer in idle operation is 220 volts and its secondary voltage is 11 volts. (Xm is magnetizing reactance, Rfe is iron resistance, values indicated by index 1 belong to primary side, values indicated by index 2 belong to secondary side) a. Calculate the secondary values reduced to primary

Equivalent circuit parameters R1 = 1ohm, X1 = 2ohm R2 = 0.0035 ohm X2 = 0.0045ohm Xm = 1100ohm Rfe = 6400ohm. The primary voltage of the transformer in idle operation is 220 volts and its secondary voltage is 11 volts. (Xm is magnetizing reactance, Rfe is iron resistance, values indicated by index 1 belong to primary side, values indicated by index 2 belong to secondary side) a. Calculate the secondary values reduced to primary

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Similar questions

a) The transformer has a turns ratio of 9.45, what is the dc load voltage considering the ripple voltage? b) The transformer has a turns ratio of 9.45, what is the dc load voltage without considering the ripple voltage?in 2 decimal places.
AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with 20 coils. What is the exiting voltage and current? a.) 1000v/0.1amp b.) 0.1v/1000amp c.)1000v/1amp d.) 2v/20amp e.) No change
Answer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohm
Describe the four tests carried out on the transformer and state their purpose
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
• If the transformer has N₁=1,000 turns and N₂ = 5,000 turns. What will be the primary Power, (P₁), comparing to the secondary power (P₂)? P1 will be 5 Times lower than P2 P1 is equal to P2 P1 is 50 times lower than P2 P1 will be 5 times higher than P2
In a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic i.e, fast system response? How about when duty cycle changes slowly i.e, slow system response?
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
What is the type of core material of the transformer? a. Iron O b. Silicon steel O c. Graphite O d. Copper
Current transformer has Select one: O a. No relation between primary windings and its secondary windings O b. More secondary windings than its primary windings O C. Primary windings equal to secondary windings O d. More primary windings than its secondary windings
2. Show full solution. Magnetically coupled circuits.
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them