Estimate power for aunealed low carrbon steel strip 200mm wide and 1omm hick, oolled to a tuick ness of 6mm. the roll radius es 200mm e the oll rotate 2002eu/min mction are the alee ueosk Use O4 coefficient aeuter face s0 A los car bon steel 以ter fae こheニ 10の Carr bon stee? Such as A 20 has K=530M pa and

Estimate power for aunealed low carrbon steel strip 200mm wide and 1omm hick, oolled to a tuick ness of 6mm. the roll radius es 200mm e the oll rotate 2002eu/min mction are the alee ueosk Use O4 coefficient aeuter face s0 A los car bon steel 以ter fae こheニ 10の Carr bon stee? Such as A 20 has K=530M pa and

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 4340 quench and tempered rotating steel shaft, d = 1 in, is loaded in fully reversed bending . The bar has been machined with surface conditions a = 1.34 ksi and b = -0.085, and will be operating at room temperature. The program requires a reliability of 99.99 percent. The fillet radii at all points is r = 0.08 in. The fatigue strength fraction f = 0.76, and the The ultimate strength (Sut) is 260 Ksi. Determine the endurance limit in the aforementioned conditions
The cold work is gevn for 15% then determine the upcoming values of its stength if the material is An annealed steel the properties of the material is Sy = 32.0 kpsi, Su = 49.5 kpsi,σf = 91.1 kpsi, σ0 = 90 kpsi, m = 0.25, and εf = 1.05 in/in. assume steel type :An annealed AISI 1018 steel please give detiled answer if expecting upvote
Please present FBD/s A tri mettalic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plate. THe bar consists of a circular stell core sorrounded by brass and copper tubes. The steel core has a diamter 10mm, the brass trube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm. E for steel =210 GPa, E for brass = 100GPa and E for copper is 120GPa. Calculate the compressive stress of each metral due to force P.
Produced from xCy steel material by machining method, the shaft is bedded at C and D points. With the shaft, constant Fy= 830 N forces in the vertical direction and constant Fx= 4,3 kN forces in the axial direction, which do not rotate together. The tensile strength of the shaft material is (sigma)tensile = 630 MPa and the yield strength is (sigma)yield = 430 MPa. For 50% reliability, analyze the fatigue damage condition of the shaft sections A and B separately.Question: How do we apply a tensile force to a part supported on both sides?Answer: We think that one of the bearings is a bearing that allows axial movement.(Take SI unit and make the solutions legit and clear please. I need an answer even though it doesn't reach a clear solution.)
Two steels are being considered for manufacture of as-forged connecting rods subjected to bending loads. One is AISI 4340 Cr-Mo-Ni steel capable of being heat-treated to a tensile strength of 260 ksi. The other is a plain carbon steel AISI 1040 with a ultimate strength of 113 ksi. Each rod is to have a size giving an equivalent diameter of 0.75 in. Determine the endurance limit for each material. Is there any advantage to using the alloy steel for this fatigue application?
How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?
A steel plate is subjected to a constant amplitude uniaxial fatigue loads to produce stresses, max = 180 MPa and min = -40 MPa. The static properties of the steel are YS= 500 MPa, UTS= 600 MPa, E= 207 GPa and Kc= 100 MPa-m1/2 . If the plate contains an initial through the thickness edge crack of 0.5 mm how many fatigue cycles will be required to break the plate. Please state any assumptions you make.
A ductile cast-iron bar is to support a load of40,000 lb in a heat-treating furnace used tomake malleable cast iron. The bar is located in aspot that is continuously exposed to 500C. Designthe bar so that it can operate for at least 10years without failing.
Steel shafts with a diameter of 0.1 m (AISI 1010) will be heat treated in a furnace with a gas temperature of 1200 K and a heat transfer coefficient of 100 W/m2K. If the spindles enter the oven at 300 K, how long must they stay in the oven for the axis temperature to reach 800 K?
Pls answer thank you! Calculate the wire diameter of a steel spring that could support a load of 50 kg. Allowable working stress is 427 x 10 6 N/m2 , the spring mean diameter is to be 44.45 mm and G = 79.3 Gpa.
20 long tons of ice per 12 hrs at -15 °C were produced from steam at 190 °C. If there is no miscellaneous losses. How many TR are required? (Use 2257 and 334 as your reference values for the latent heats and 4.187 for the value of specific heat of water).
A solid cylindrical shaft made of AISI 1020 steel(quenched and tempered at 870oC) rotates at a speedthat produces a safety factor of 2.5 against the stresscausing yielding. To instrument the shaft, a small hole isdrilled in its center for electric wires. At the same timethe material is changed to AISI 1080 steel that has beenquenched and tempered at 800oC. Find the safety factoragainst yielding of the new shaft.