Example 07:- For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 = R3 = R4 = 1002 2- R1 = R2 = R3 = 100n and R4 = 1202 Consider the circuit use an ideal Op-Amp and its resistances do not load the bridge circuit. 12K 10K 10V 10K 12K ww

Example 07:- For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 = R3 = R4 = 1002 2- R1 = R2 = R3 = 100n and R4 = 1202 Consider the circuit use an ideal Op-Amp and its resistances do not load the bridge circuit. 12K 10K 10V 10K 12K ww

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Related questions

Q: Given: R1, R2. Assume that the op-amp is ideal. R2 R1 R1 Given: v2 and vi = 0 V, determine the…

A: Given : Here we have mentioned the operational amplifier is ideal. The ideal characteristics of…

Q: H.W. 2: Design an inverting op-amp circuit for which the gain is -10 and the to resistance used is…

Q: As an Electronic Engineer in XYZ Analog IC Design Centre, you are required to design Operational…

Q: Q3 A differential amplifier is constructed using an ideal op-amp as shown in the adjoining figure.…

A: Given V1 = 1 V, r1= 13000 Ohm V2 = 1 V, r2 = 3000 Ohm R1 = 47000 Ohm R2 = 470000 Ohm Formula used…

Q: Enample 07:- For the circuit shown in the figure, calculate the output voltage when R1 = R2 = R3 =…

Q: Figure Q1 shows the circuit diagram of a "Logarithmic Amplifier". In this circuit the feedback…

Q: Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is…

A: In this question , cascaded configuration of opamp is given...We have to find out gain of 3rd…

Q: For the Op.-Amp. circuit below, find the gain for each branch, VOUT equation, draw the resultant…

Q: ov- -5V- V(vo1) 12V- ov -12V V(v2) V(vnoise) 5V- -5V- V(vo2) 12V

A: Due to the presence of noise as it can be seen from the simulation diagram given the output v01,…

Q: Consider the op-amp circuit below. (a) Find the expression of vout in terms of vin. (b) Sketch the…

Q: Q1: design an inverting op-amp circuit to form the weighted sum Vo = -(vị + 4v2) .choose the values…

A: The solution is given below

Q: Yo= Ad Va (i+ cmer Problem#2 CMRR Vd Determine the output voltage of an op-amp for input voltages of…

A: In the op-amp, we used the model basic mathematic operations like addition, subtraction,…

Q: Show the connection of two op-amp stages using an LM358 IC to provide outputs that are -25 and 40…

A: The required circuit can be designed by cascading inverting and non-inverting amplifiers. The…

Q: 4k2 5kN 3mA 3kN 2kN 1kN Determine for the above ideal op-amp circuit, Vo lo, and the power…

Q: 2. The voltage measuring function V = f(V,) that is implemented by a differential op-amp circuit in…

A: Operational Amplifier A three-terminal device consists of two high impedance (Inverting and…

Q: b) Draw an amplifier circuit using an ideal op-amp that computes the average of 3 input signals.…

A: According to the question, we need to draw the circuit by using OP-AMP, which can compute the…

Q: For the Op.-Amp. circuit below, find the gain for each branch, VOUT equation, draw the resultant…

Q: Draw the circuit diagram of the basic inverting amplifier configuration. Give an expression for the…

A: The below figure shows the basic inverting amplifier. Here, the input is applied to the inverting…

Q: The op-amp is specified to have a slew rate (SR) of I V/us. Consider the circuit below and clearly…

A: The output of Non inverting amplifier is in phase with input. The Non inverting Amplifier is shown…

Q: Draw a circuit diagram of a 311 op-amp showing an input of 10 V as with f= 1KHZ, applied to the…

A: Given data : Vin=10Vf=1KHzRefrence voltage applied to 2Vref

Q: | H Design OP-Amp oircwt that Poduce an out Rut an given by Uo = - (4U,+ Uz toil V3) If U, = 2 sinwt…

A: The output voltage is negative. Hence the given op-amp is inverting op-amp. There are three input…

Q: Example 07: For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 = R3 =…

Q: An operational amplifier (op-amp) is shown in Figure Q2(a). Given R; = 15 k2, Rf = 100 k2 and supply…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A generic op-amp circuit is shown in Figure 3. VWith the given data, answer the ollowing by showing…

Q: 1. The op-amp in the circuit is ideal, except for non-zero input bias currents. Further, R1 =10K and…

A: Given:R1=10kR2=30k Circuit diagram:

Q: (a) An operational amplifier shown in Figure 1. Sketch the real circuit model of the amplifier. As a…

A: We are answering all questions in short. It is asked to sketch the real circuit for an operational…

Q: Derive the voltage gain of the circuit given, assuming it is an Ideal Op- Amp. If R1=2k, R2=10K2 and…

Q: Q1 A cascaded op-amps that can total up values of three voltage inputs V1 = 5V, V2=8V and V3 = 10V…

Q: Here is a single op-amp, shown under two different conditions (different input voltages). Determine…

Q: 5) or the circuit shown below, if the differential gain (Aa) of the op-amp is (50000) and the CMRR -…

A: In this question, if the differential gain Ad of the op-amp =50000 CMRR in (db) = 34 Find the…

Q: Draw the circuit diagram of the basic noninverting amplifier configuration. Give an expression for…

A: In an ideal op-amp, voltage at inverting and non-inverting terminals are equal. and current is zero.…

Q: Consider the bistable circuit below left with the positive input terminal of the op-amp connected to…

A: (a) The operational amplifier's positive-input terminal is connected to a positive voltage source V…

Q: For the given op-amp circuit,

A: NOTE- “Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: (a) For the op-amp circuit shown in Figure Q1(a): (i) Derive the mathematical expression for an…

A: Given the circuit: Given the values: V1=3 mV, V2=5.9 mV, V3=8.9 mV, R1=200 kΩ, R2=509 kΩ, R3=Rf=1…

Q: For the Op.-Amp. circuit below, find the gain for each branch, VOUT equation, draw the resultant…

A: The circuit given is of inverting op amp . The total output will be the sum of individual outputs.…

Q: For the above circuit determine the Op-Anmp output current I, Amps (Note: This is not the current…

Q: TRUE OR FALSE 1. Due to the infinite open-loop volatge gain of an ideal op-amp, its diferrential…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost the other…

Q: For the ideal op-amp shown, what should be the value of resistor Rf (in kilo Ohms) to obtain a gain…

Q: In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and…

A: The given problem is from voltage regulator. The calculation is shown in the next step

Q: In the op-amp circuit given in the figure, the load current i, is R2 a. Vs R2 O b. - Vs R2 O c. Vs…

Q: 4. (a) Determine the input and output impedances of the amplifier in Figure - 2. The op-amp…

A: Zin = 1.2 MohmZout = 120 ohmAOL = 150000

Q: Example 07:- For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 = R3…

Q: A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing…

Q: F. Design an op-amp circuit that performs the following mathematical operation: V, + V, + V3 + V,…

A: Given output voltage is given as V0=V1+V2+V3+V44. Now as it is asked to design the op-amp circuit so…

Q: Perform the block diagram given on the side using an op-amp.

A: Circle representing adder Triangle representing opamp

Q: 7 Figure P8.27 shows a simple practical amplifier that uses the 741 op-amp. Pin numbers are as…

A: The circuit diagrams are shown below: Since the open-loop gain of the op-amp is very large also the…

Q: For the Op.-Amp. circuit below, find the gain for each branch, VOUT equation, draw the resultant…

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

Example 07:- For the circuit shown in the figure, calculate the
output voltage when
1- R1 = R2 = R3 = R4 = 1002
2- R1 = R2 = R3 = 100N and R4 = 1202
Consider the circuit use an ideal Op-Amp and its resistances
do not load the bridge circuit.
12K
10K
E
10V
10K
12K
ww

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The input-output relationship for the inverting op amp circuit is given ideally by: Vo = (-R f / Ri)Vi . The closed loop gain of the amplifier circuit is calculated as G = Vo/Vi. Use these equations to calculate the the expected output voltage and gain of the opamp circuit given
a.Realize a circuit to obtain Vo=5V1-2V2+3V2 using op-amp connected in an inverting mode, Where V1, V2and V3 are positive input signals connected. take the value of feedback resistors as 100ohms. b.An op-amp has a feedback resistor Rf =25kiloohms and the Rs1=6kiloohms, Rs2=10kiloohms, Rs3=5kiloohms. The corresponding inputs are Vi1=-15v, Vi2=4, Vi3=12. The non-inverting terminal is grounded. calculate the total Voltage.
Given circuit, assume op-amp is ideal. What is the input resistance of the circuit, RIN? What are the currents in the inputs of op-amp? i-=? i+=? What is the output resistance of the circuit, ROUT=? Find voltage VA and VB? What is the nodal equation (KCL) at node VB? Solve for VOUT=?
An ideal op-amp circuit is shown above, with dc supply Vcc = -Vcc = 12V. Assume that vs = 3V, R1 = 2Ω, Rf = 4Ω. Please find the output voltage vo in volts.
Graphically show the output voltage (Vo) and load current (IL) by simulating the difference receiving Op-Amp circuit given in the figure.(PSIM using PSpice or)R1 = R2=10kΩRL=1.5 kΩRf=14kΩ
In an Op-Amp Differential Amplifier, how should I find R1 and R4 when V1, V2, VOUT, and IR1 are given? Hint: R1 = R3, and R2 = R4
Find the output voltage vO in the following figure if the op-amp is ideal and VZ = 12 V. Find the values of the emitter current and the total current supplied by the 15-V source. Assume βF = 62. Find the op-amp output voltage. Given that R1 = 53 kΩ and R2 = 104 kΩ.
In the figure, there is an ideal opamp connected to a resistor set from the non-inverting input in the circuit. The resistor set on the left feeds the circuit with different voltages while the switches below touch the resistors RA, RB, RC of different values. a.) If we call the input voltage Vi from the left resistor set, derive the expression that gives the Opamp's Gain. b.) Assume a fixed 10V output is read at the output of the circuit. In this case, if the current (I) is 100mA, 10mA and 1mA while the resistors A, B and C are installed, calculate the values of these resistors RA, RB and RC.
a) Design a non-inverting amplifier using an ideal op amp that has a gain 7.5.b) If you wish to amplify signals between -2V and 1.2V using the circuit you designed in part (a) what arethe smallest power supply voltages you can use?c) Draw your final circuit diagram.d) Assume that the voltage signal source is vs = −1V and the feedback resistor Rf is replaced with avariable resistor. Specify the range of Rf (in kΩ ) which will cause the op amp to saturate?
Write down the characteristics of an ideal op-amp. Design an op-amp circuit with inputs v1, v2and v3 such that v0= -3v2 + 0.5v1 + 2v2.
For the circuit shown above, find an expression between the inputs, v1, v2, v3 and v4 and vO. Make simplifying assumptions about the OP-AMP such as v+=v- but you must state the conditions for which this assumption is correct. As soon as possible！
Consider the active circuit with the schematic: (ONLY ANSWER C-E) a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.