Example 10.4 A thin closed cylindrical shell of steel made of 7.5 mm thick plate is filled with water under a fluid pressure 5 N/mm2. The internal diameter of cylinder is 250 mm and its length is 2000 mm. Calculate the amount of water spilled when shell is opened. Take E = 2 x 105 N/mm2, u = 0.30 and k. = 2100 N/mm2

Example 10.4 A thin closed cylindrical shell of steel made of 7.5 mm thick plate is filled with water under a fluid pressure 5 N/mm2. The internal diameter of cylinder is 250 mm and its length is 2000 mm. Calculate the amount of water spilled when shell is opened. Take E = 2 x 105 N/mm2, u = 0.30 and k. = 2100 N/mm2

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the pressure required to decrease the volume of the oil by 2%?
As shown in the figure, water flows in the horizontal pipe. The pipe consists of two different sections, 60 mm and 30 mm in diameter, connected by a smooth reduction. The pressure difference between the two sections is measured with a mercury manometer. Friction effects are neglected. The height between the mercury levels in the two sections of the pipe was determined as 1.4m. Find the velocity and mass flow at points 1 and 2. (Density of mercury: 13.6 grams / cm3, Density of water: 1gr / cm3)
Oil flows through a pipe as shown in the figure below. The coefficient of discharge for the orifice in the pipe is 0.85. What is the discharge of oil in the pipe in L/s?
A pressure in a given tank reads 265 mm of Hg. Determine the equivalentheight of a certain fluid in m with sp. gr = 3.44.
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: (a) Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 45.15 in. (b) Fluid A is water, the gage fluid is air, and z = 15.15 in.
Please show the complete solution. (Example: Conversion of Units) A rigid container is closed at one end and measures 8 in diameter by 12 in long. The container is held vertical and is slowly moved downward until the pressure in the container is 17 psia. What will be the depth of the top of the container from the free water surface?
A pipe 10mm in diameter is fitted to a water tank as shown in figure 4. The nozzle 25mm in diameter at the end if the pipe discharges into the atmosphere. Calculate the flow rate and pressure at B.
For the manometer shown in the image, all fluids are at 20 degrees C. If PB-PA = 89.5 kPa, determine the height H in centimeters. The specific weight of water is 9790 N/m^3 and the specific weight of mercury is 133100 N/m^3
In the figure below, pipe A contains gasoline (S.G.=0.75), pipe B contains oil (S.G.=0.91) and the manometer fluid is mercury (S.G.=13.6). The initial differential reading is 0.30m as shown. Determine the pressure difference between A and B.
A container is filled with different layers of various liquids, as shown in the figure,Determine: a) the pressure difference between the top surface and the bottom of the cylinder and b) the pressureabsolute at the bottom of the cylinder if the atmospheric pressure is equal to 100Kpa. solve step by step
The water flow rate in the pipe will be measured using the pitot tube system given in the figure. At point 1, the velocity is zero and represents the stationary point. Since there is mercury with a density of 13600 kg/m3 in the manometer and the height of the manometer is read 0.06, calculate the volumetric flow rate of the water flowing in the pipe with a diameter of 0.2 m. (ρwater = 1000 kg/m3)