EXAMPLE 12.1 Calculate the input power, output power, and efficiency of the amplifiercircuit in Fig. 12.5 for an input voltage that results in a base current of 10 mA peak.Vcc = 20 VAlc (mA)Vec 20 VIc=401000Rc 20290080030IcRc = 20 2700de load lineRB1 kQC;7060020Ise500Ice400Operating pointB = 2530010200100I =0 mAII510152025VCE (V)VCE = Voc

Answered: Image /qna-images/answer/7e027afc-7936-4dc1-a206-7f0f2f1b650b.jpg

EXAMPLE 12.1 Calculate the input power, output power, and efficiency of the amplifier circuit in Fig. 12.5 for an input voltage that results in a base current of 10 mA peak. Vcc = 20 V (mA) Voc 20 V - 1000 Re 200 900 Rc = 202 de load line 700 1 k2 C 600- 20 500 Ice B = 25 Operating point 400 300 10 200 100 -0 mA 10 15 20 25 Va (V) Va= Vee

EXAMPLE 12.1 Calculate the input power, output power, and efficiency of the amplifier circuit in Fig. 12.5 for an input voltage that results in a base current of 10 mA peak. Vcc = 20 V (mA) Voc 20 V - 1000 Re 200 900 Rc = 202 de load line 700 1 k2 C 600- 20 500 Ice B = 25 Operating point 400 300 10 200 100 -0 mA 10 15 20 25 Va (V) Va= Vee

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given a certain common-source JFET amplifier in the laboratory, RD = 1 KΩ, RS = 560 Ω, VDD = 10 V and gm = 4500 uS. If the source resistor is completely bypassed, what is the voltage gain? _________- (hint: the voltage gain is the product of total AC load resistance and transconductance. Getting the total AC load resistance is equal to the parallel of load resistance and RD for loaded circuit)."
How experimental setup is prepared for a CE transistor configuration. Drawits a h-parameter model. Find amplifier parameters given below using this model- (i) Current gain(ii) Input impedance(iii) Voltage Amplification (AVS) consideration source impedance(iv) Current Amplification (AIS) consideration source impedance
Since the transistors used in the circuit are B=100, ro=∞ a) Find the re1, re2 resistance values by performing the DC analysis for each amplifier stage separately. b) Draw the AC equivalent circuit of the amplifier circuit. c)Find the input and output impedance values for each amplifier stage. d) Find the voltage gains AV1, AV2 for each amplifier stage. e) Find the voltage value VL by finding the AV1 Voltage gain.
The ac equivalent circuit for an amplifier is shown. Assume the capacitors have infinite value, RI = 100 kΩ, RG = 6.8MΩ, RD = 50 kΩ, and R3 = 120 kΩ. Calculate the voltage gain for the amplifier if the MOSFET Q-point is (100 μA, 5 V). Assume Kn = 450 μA/V2 and λ = 0.02 V−1.
The ac equivalent circuit for an amplifier is shown. Assume the capacitors have infinite value, RI = 100 kΩ, RG = 10 MΩ, RD = 560 kΩ, and R3 = 1.5 MΩ. Calculate the voltage gain for the amplifier if the MOSFETQ-point is (10 μA, 5 V). Assume Kn = 100 μA/V2 and λ = 0.02 V−1.
What are the unity-gain frequency and slew rate of the bipolar amplifier as shown if I1 = 100 μA, I2 = 400 μA, and CC = 10 pF? (b) If I1 = 300 μA, I2 = 350 μA, and CC = 10 pF?
Given a Class A amplifier given a VCEq = 10.5V, VCC = 24V, Voltage divider resistors 1kohm and 180ohm, Ic = 40mA. Calculate the Po(ac) = mW (Note this is in mW. Round to the tens place.) Calculate the DC power dissipated = Watts (enter to the tenths place) Calculate the efficiency percentage = % Round to the ones place (no decimal places).
Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
Given the transformer-coupled cascaded bjt amplifier circuit Determine: a. Av2=Vc2/Vb2 b. Av1=Vc1/Vb1 c. Vo if Vs=0.5mVp-p d. Ais=Io/Is
Given r_e = 10 Ω, β = 200, A_v = -160, and A_i = 19 for the collector-feedback network shown below, determine a) R_C; b) R_F; and, c) V_CC .
A common emitter amplifier as shown in Figure Q2 has the following parameters, β = 100, R1= 33K, R2 = 10K, RC = 3K3, RE = 1K, ro =  and VBE = 0.7 V.State all assumptions made.i. Check whether βRE>>10R2 is satisfiedii. Use the appropriate approach of analysis to determine the Quiescent point; IBQ,ICQ and VCEQ.iii. Draw the small signal equivalent circuit. Determine input impedance, Zin, outputimpedance, Zout, and the voltage gain, AV, if RL=20kΩ.
Use BJT transistor to design an amplifier circuit that operates in the frequency range 10kHz-100kHz. Verify your design by simulating the design using the circuitmaker or multisim software. Use the standard resistor values (10% tolerance). The design should meet the following criteria: 1. Good stabilization of the Q-point 2. VCEQ is around ½ VCC. 3. High voltage and Current gain. From your design and simulation results, determine the following: a. β of the transistor b. VCEQ c. The voltage gain (AV) Please provide us with your simulation file and a report about your results