a. No need to copy the problems. b. Computation must be complete. Answer in two decimol places. d. Use only ball pen/ ink pen. e. Box your final answer. C. PROBLEM No.1 A torque T = 1500N – m is applied to the hollow shaft shown that has a uniform 10 mm wall thickness. Determine the shearing stress at points a and b, and the angle of twist if its length is 2 m and G = 65 GPa. Express your answer in shear in MPa and angle of twist in degree units. 100 mm- b 75° a

a. No need to copy the problems. b. Computation must be complete. Answer in two decimol places. d. Use only ball pen/ ink pen. e. Box your final answer. C. PROBLEM No.1 A torque T = 1500N – m is applied to the hollow shaft shown that has a uniform 10 mm wall thickness. Determine the shearing stress at points a and b, and the angle of twist if its length is 2 m and G = 65 GPa. Express your answer in shear in MPa and angle of twist in degree units. 100 mm- b 75° a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Torsion Problem: A solid circular shaft of diameter 220 mm is to be replaced by a hollow shaft in which the ratio of the diameters is 2:1. Determine the size of the required to transmit the same torque as the solid shaft at the same maximum shearing stress.
The stepped shaft shown rotates at 480 rpm. Knowing that r = 0.2 in. and using figure 3.28, determine the largest torque T that can be transmitted without exceeding an allowable shearing stress of 7000 psi.
A hollow steel tube has an outside diameter of 227 mm and inside of 208 mm. Which of the following gives the maximum torque in kJ that it could carry if the allowable shearing stress is 84 MPa.
(13) A 4-in diameter solid shaft is to be replaced with a hollow shaft equally strong and made of the same material. The outside diameter of the hollow shaft is to be 5-in. What should be the inside diameter for an allowable shearing stress of 6,000psi.
Give a complete solution, Don't use the direct formula. [1] A semicircular groove with a 5-mm radius is required in a 110-mm diameter shaft. If the maximum shearing stress in the shaft must be limited to 60 MPa, determine the maximum torque that can be transmitted by the shaft.
What is the maximum allowable torque in kN-m for a 50 mm diameter steel shaft when the allowable shearing stress is 81.50 MPa.
what horsepower can be transmitted by 1/2 in. diameter solid shaft at 1800 rpm if the allowable torsional shearing stress is 6000 psi?
The transmitted torque of a hollow shaft is 3400 N-m at a shearing stress of 55 MPa. If the outside diameter is 1.25 times that of the inside diameter, what is the inside diameter, in mm?
Given: Diameter of pin at B = 20 mm Required: Shearing stress of the pin at Br
Pls answer thank you! . A 10-spline shaft ( d= 0.91D, w= 0.156D, h= 0.045D ) and permanent fit has a diameter of 70 mm. Find the shearing stress if shearing force is 2000 lbs.
200 HP is delivered by a solid circular shaft at 1000 rpm rotational speed. If a hollow shaft is used having an inside diameter equal to the diameter of the solid shaft, determine what must be the outside diameter of this shaft if the angular twist of the hollow and solid shaft is to be equal? The allowable maximum shearing stress is 20,000 psi.
Determine the torque in ft-Ib that can be applied to a 1-in diameter circular shaft if the shearing stress is not to exceed 8000 psi.