Example 6: Find the angle of inclination with respect to the vertical of a two wheeler trying to turn. Given that:combined mass of the vehicle with its rider is 250 kg: moment of inertia of the engine flywheel is 0.3 kg-m';moment of inertia of each road wheel is 1 kg-m2; speed of engine flywheel is 5 times that of road wheels and inthe same direction; height of center of gravity of rider with vehicle is 0.6 m; two wheeler speed is 90 km/h; wheelradius is 300 mm; and radius of turn is 50 m.

Given: v=90 km/hr=25m/s R=50 m r=300 mm = 0.3 m Iw= 1 kg.m2 Ie= 0.3 kg.m2 m=250 kg h=0.6 m G= 5-the…

Example 6: Find the angle of inclination with respect to the vertical of a two wheeler trying to turn. Given that: combined mass of the vehicle with its rider is 250 kg: moment of inertia of the engine flywheel is 0.3 kg-m; moment of inertia of each road wheel is 1 kg-m; speed of engine flywheel is 5 times that of road wheels and in the same direction; height of center of gravity of rider with vehicle is 0.6 m; two wheeler speed is 90 km/h; wheel radius is 300 mm; and radius of turn is 50 m.

Example 6: Find the angle of inclination with respect to the vertical of a two wheeler trying to turn. Given that: combined mass of the vehicle with its rider is 250 kg: moment of inertia of the engine flywheel is 0.3 kg-m; moment of inertia of each road wheel is 1 kg-m; speed of engine flywheel is 5 times that of road wheels and in the same direction; height of center of gravity of rider with vehicle is 0.6 m; two wheeler speed is 90 km/h; wheel radius is 300 mm; and radius of turn is 50 m.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.49P

See similar textbooks

Similar questions

For the following figure b is the distance to the center of gravity of the arm segment, W is the weight of the arm of mass, m, moving the arm in abduction/adduction. If we had radius of gyration ratio to segment k's (k1 is for the Antero-posterior axis, k2 is the transverse axus, and k3 is for the longitudinal axis of the segment). What is the mass moment of inertia?
Two masses A and B are 5kg and 2kg respectively rotating in a shaft. The corresponding radii of rotation are 0.2m and 0.3m respectively and the angle between the masses is 600. Find the position and magnitude of the balance mass required, if its radius of rotation is 200 mm using graphical method and also verify your answer with analytical method.
A circular solid disc of uniform thickness 20 mm, radius 200 mm and 20 kg, is used as a flywheel If it rotates at 600 rpm, what is the kinetic energy of the flywheel.
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
A flywheel with moment of inertia 0.8kgm2 rotates with a speed corresponding to 8 revolutions per second. What is the rotational kinetic energy of the flywheel?
Consider a pulley system shown below. Assume there is no slip between the cord and the pulley. I is the mass moment of inertia of the pulley about its own centroidal axis. Find the equations of motion in terms of x. Select all that apply.
If a disk (radius R) is subjected to two tangential forces of equal value and accelerates initially, but then reaches a constant angular velocity how would you represent the torque acting upon the center of the desk?
A Volkswagen Bug weighing 3,045 lb is design with a wheelbase of 100.1 in has a center ofgravity that is 17 in above the pavement and 25 in behind the front axle. If the car is on aroadway with packed snow or ice, what is the maximum tractive effort that can be developed ifthe car is (a) front-wheel drive or (b) rear-wheel drive?
Suppose a 30 lb truck wheel 18 in. in diameter has a radius of gyration of 4 in. and the 6120 lb truck’s weight is distributed equally to each of the four wheels.a. If the truck can supply 150 lb x ft of torque to each wheel, how fast would the wheel want to accelerate if it didn’t slip? b. What would the coefficient of friction have to be in order to keep the wheel from slipping
Consider a disc of mass, M with radius 0.5 m on a slope with angle 45 degrees to the horizontal. It has a good grip on the slope and does not slip. The disc is constructed so that its mass per unit area, ρ(r) = r1/2 kg m−2, with r being the radial distance in metres from the axis of the disc. What is the equation describing the linear acceleration of the centre of mass of the disc down the slope in terms of the angular acceleration of the disc.
During a bicep curl on a bicep curl machine, I'm curling a weight stack of 100 pounds (single arm...I'm jacked like that). At this very moment, the weight stack has a moment arm of 0.12m, my elbow has an angle of 63deg, my muscle force vector has an angle of 23deg, and it attaches 3cm below my elbow joint on my radius. How much force must my bicep create right at this moment to hold the weight stack in place?
A weight of 500 kg is being lifted up at a uniform speed of 1.5 m/s by a winch driven by a motor running at a speed of 1000 rpm. The moments of inertia of the motor and winch are 0.3 and 0.3 kg-m respectively. In the absence of the weight, the motor develops a torque of 100 Nm at a speed of 1000 r/min. Calculate the motor torque and the equivalent moment of inertia referred to the motor shaft