Example 7: The experiments set-up given below measuresthe value of unknown resistance in two steps.SVSwitch www2RG• When V = 24 V, r is set at 400 52 and 5=802, galvanom-eter shows a deflection of 30°.• When switch is thrown to position 2 the supply voltagedrops down to 22 V and the galvanometer still shows adeflection of 30°.The value of unknown resistance Ris(A) 80 22(C) 40(B) 609(D) None of the above

Example 7: The experiments set-up given below measures the value of unknown resistance in two steps. Switch 2 R G • When V=24 V, r is set at 400 52 and 5=8052, galvanom- eter shows a deflection of 30°. The value of unknown resistance Ris (Λ) 80 Ω (C) 40 S • When switch is thrown to position 2 the supply voltage drops down to 22 V and the galvanometer still shows a deflection of 30°. (B) 60 (D) None of the above

Example 7: The experiments set-up given below measures the value of unknown resistance in two steps. Switch 2 R G • When V=24 V, r is set at 400 52 and 5=8052, galvanom- eter shows a deflection of 30°. The value of unknown resistance Ris (Λ) 80 Ω (C) 40 S • When switch is thrown to position 2 the supply voltage drops down to 22 V and the galvanometer still shows a deflection of 30°. (B) 60 (D) None of the above

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
Help me answer, I want to check my solution To get the contribution of the 75V source to iR, we first kill the 50mA source. What is the resulting equivalent resistance in series with the 75K resistor (in Kohms) To get the contribution of the 75V source to iR, we first kill the 50mA source. What is the resulting value of iR (in mA)? What is the nodal equation for Vx? What is the Thevanin voltage in (Volts) and Thevanin resistance in (Kohms)?
2. In a circuit that contains only resistors in parallel, some of the current in the circuit will go through each branch of the parallel resistors, as dictated by Kirchoff's Junction Rule. Furthermore, the potential difference provided by the battery is the potential difference across each branch of the parallel resistors (notice there is no potential drop between the branches). Assume the batteries supply a potential difference of AV = 3.0 V, and use Ohm's Law along with the currents measured through resistor R1 in circuits 4a, 4b, and 4c to determine the effective resistance in this branch (the branch that includes R1) of each circuit. Please show the calculation of each. R1 = 150 ohm, R2 = 230 ohm R3 = 270 ohms (don't believe question should need these but providing anyways)
Q21 A PMMC instrument gives 25 mA at full scale reading when a potential difference across its terminals is 32mV. Show that how it can be used (a) as an ammeter for the current measurement in the range of 0 –3 A (b) as a 0 – 510V range voltmeter for the voltage measurement. (c) find the multiplying factor of shunt and AND voltage amplification
Need help with this Question The D-MOSFET circuit shown in Figure Q1(b) has IDSS = 3 mA and VGS(off) =−8 V. Given the following:R1 = 50 kΩR2 = 150 kΩRD = 1 kΩRS = 2 kΩVDD = +10 VVSS = −10 VDetermine VGS, ID and VDS.
Look at the images shown. Why can we measure resistance with a pencil drawn on a piece of paper? What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance? 0.449 mega ohms 102.2 kilo ohms
Please help me solve for the total resistance, total current, and individual voltage if: VT = 30 VR1 = 7 ohmsR2 = 10 ohmsR3 = 6 ohmsR4 = 4 ohmsR5 = 8 ohmsR6 = 9 ohmsR7 = 5 ohmsR8 = 12 ohmsR9 = 3 ohmsR10 = 8 ohms
4. The heating element in an oven has a resistance of R =32 ohms. One of thewires connecting the oven to the 220 volt power source is loose, contributingan additional r = 5 ohms to the closed-loop circuit. What is the power Povenradiated in the oven, and what is the rate Pcontact at which heat is dissipatedat the loose contact? The looser is the connection, the greater is the resistance r: What value of r is most likely to cause a fire. Also agraph showing Pcontact versus r
following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
QUESTION TEXT A potentiometer consisting of a wire of length = 10 cm has a source of emf, ɛ = 15V connected across it. When a standard cell with emf V = 6V, in series with a voltmeter, is connected at one end of the wire and at a distance L along the wire the voltmeter circuit is in balance and the voltmeter reads zero. What is the value of the balance length L? Select one: a. 1.5 cm b. 4.0 cm c. 6.0 cm d. 2.0 cm
The diagram shows an ideal (zero internal resistance) DC source connected to three identical resitances and a switch. In the diagram, the switch is open. If initially, the switch is open, what happens to current I1 and I2 after the switch is closed?
If the same meter movement in no.4 is used to construct a multi range voltmeter whose ranges are 5 V, 10 V and 15 V, find the required resistances for the following configuration: a. Basic multi-range voltmeter b. Commercial multi-range voltmeter (given in no.4: A 3-V DC voltmeter is composed of a 500-Ω meter movement in series with a 2500-Ω series resistance.)