Example: A balanced positive-sequence wye-connected 60 Hz three-phase source has line-to- line voltages of V,=1000 V. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.2 H inductance in series with a 100 0 resistance. Find the line-to-neutral voltages, the line currents, the power, and the reactive power delivered to the load. Assume that the phase of Von is zero.

Example: A balanced positive-sequence wye-connected 60 Hz three-phase source has line-to- line voltages of V,=1000 V. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.2 H inductance in series with a 100 0 resistance. Find the line-to-neutral voltages, the line currents, the power, and the reactive power delivered to the load. Assume that the phase of Von is zero.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a) Develop an expression for the reactive power Q in terms of ,L, and I, from complex power considerations. (b) Let the instantaneous current be i(t)=2Icos(t+). Obtain an expression for the instantaneous power p(t) into L, and then express it in terms of Q. (c) Comment on the average real power P supplied to the inductor and the instantaneous power supplied.
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
A 480V single phase load has resistance of 70 ohms and inductive reactance of -j45 ohms. Find the real power, the apparent power, and the power factor consumed by the load.
A balanced wye-connected three-phase source has line-to-neutral voltages of 440 V rms. Find the rms line-to-line voltage magnitude. If this source is applied to a wye-connected load composed of three 30-Ω resistances, find the rms line-current magnitude and the total power delivered.
A balanced positive-sequence wye-connected 60-Hz three-phase source has line-to-line voltages of VL = 440 V rms. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.5-H inductance in series with a 30-Ω resistance. Assume that the phase of VanVan is zero. FIND Ia,Ib,Ic, Find the power delivered to the load And Find the reactive power delivered to the load.
circuits A balanced 3-phase Y-connected source has using positive phase sequence, ?an = 390∠30˚ ?. Find the complex expression of voltage Eab.
The three-phase balanced load system shown in the figure will be analyzed in a continuous sinusoidal state.a) Find the total active and reactive power consumed in the load, with vR (t) = Cost Volt, Z∆ = α + βj,Find the phasor values of Ir, Is and It line currents.b) C capacities are connected to the circuit in order to provide compensation, C capacityCalculate what the value should be. α=3, β=8
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the voltage and current at R1, total power (apparent) delivered by the current source, draw the phasor diagram of the voltage and current at the source. Also, is the circuit inductive, capacitive, or neither (resistive)? please give the step-by-step solution NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
A balanced wye-connected three-phase source has line-to-neutral voltages of 240 V rms. Find the rms line-to-line voltage. This source is applied to a delta-connected load, each arm of which consists of a 10-Ω resistance in parallel with a +j5-Ω reactance. Determine the rms line current magnitude, the power factor, and the total power delivered.
1.1 We have two loads in delta and another in star in parallel, the impedances of the branches of the delta are equal and we have that RΔ=1p.u. and XΔ=0.75 p.u., while in the star we have equal values of the branches, but formed by admittances where we have the conductance in parallel GY=0.64 p.u. and inductive susceptance of BY=-j0.48 p.u. If the loads are being supplied by a positive sequence balanced three-phase source with line-to-line voltage of phases a and b of Vab=1∠ 30º, if the base values are line-to-line base voltage of 1kV and three-phase base power of 100kW. DetermineA) Line and phase voltages, line and phase currents of the load in delta, line and phase voltages of the star, line and phase currents of the star.B) Obtain separately the phasor diagram of the delta and star load with the values obtained in A), indicate on the scale that these are 1 p.u.=5cm for example.C) obtain the power triangle and the power factor separately for each load. D) Obtain the power…