EXERCISE 3 Figure shows a beam made from material A and material B. If it is known that the allowable bending stress fo material A and B is 180 MPa and 60 MPa respectively, determine the maximum moment M that can be applied to the beam. It is given that E= 200 Gpa E= 100 GPa. Justify your answer Ans M: 128 kN. m 50 mm 200 mm M 175 mm

EXERCISE 3 Figure shows a beam made from material A and material B. If it is known that the allowable bending stress fo material A and B is 180 MPa and 60 MPa respectively, determine the maximum moment M that can be applied to the beam. It is given that E= 200 Gpa E= 100 GPa. Justify your answer Ans M: 128 kN. m 50 mm 200 mm M 175 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cold drawn steel rod of circular cross-section is subjected to a variable bending moment of 565 Nm to 1130 N-m as the axial load varies from 4500 N to 13 500 N. The maximum bending momentoccurs at the same instant that the axial load is maximum. Determine the required diameter of the rodfor a factor of safety 2. Neglect any stress concentration and column effect. Assume the followingvalues:Ultimate strength = 550 MPaYield strength = 470 MPaSize factor = 0.85Surface finish factor = 0.89Correction factors = 1.0 for bending= 0.7 for axial load
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m?
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m? Use the area method
W=464KN/m Using Three Moment Equation, determine all reactions at supports also, determine shear and bending moments with complete labels. Use I= 1/12 bh^3 and E = 2.15x10^7 KPa
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
The composite beam consists of a wood core and two plates of steel. If the allowable bending stress for the wood is (sallow)w = 20 MPa, and for the steel (sallow)st = 130 MPa, determine the maximum moment that can be applied to the beam. Ew = 11 GPa, Est = 200 GPa.
1. A thin high-strength steel plate having a thickness of 40 mm has a height of 120 mm and length of 350 mm, is subjected to a moment at both ends = 66 kN.m. E = 28000 MPa Determine the bending stress of the steel plate in MPa a. 1440 b. 1855 c. 1344 d. 2063 e. 2333 Determine its radius of curvature in mm. a. 272 b. 558 c. 154 d. 434 e. 166 2. According the NSCP 2015, the first hoop for beams and girders shall be located not more than 50 mm from the face of the supporting columns. The maximum spacing of hoops shall not exceed... a. 150mm b. d/4 c 6 times bar diameter d. all of the above 3. Based on NSCP 2015 Seismic requirement on concrete girders (beams with special moment frames, which of the following most nearly gives the required width (bw) of beam if its overall height is 600 mm. a. 250mm b. 180mm c. 300mm d. 350mm e. 400mm PLEASE ANSWER ALL
Determine the bending strain energy in the simply supported beam. EI is constant.
An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm thickand the web is 20mm thick. Determine the maximum bending moment that should be imposed in the sectionif the tensile or the compressive stressis not to exceed 40MN/m^2 and what percentage of the moment is resisted by flange or web?
A beam with a circular cross section of radius c is subjected to pure bending, and it is made of a material with an elastic, perfectly plastic stress–strain curve, Eq. 12.1. Show that the moment M is related to εc, the strain at y = c, by where (a) applies for (εc ≤ εo), and (b) applies for (εc ≥ εo), with εo = σo/E being the yield strain, and α = εc/εo.
The beam is made of elastic perfectly plastic material for which sY = 345 MPa. Determine the maximum elastic moment and the plastic moment that can be applied to the cross section.
A beam is subjected to equal 19.1 kip-ft bending moments. Assume ty = t2 = ty= 1 in., d = 10 in, by= 4 in., and b2 = 7 in. The cross- sectional dimensions of the beam are illustrated. Determine; (a) the distance y to the centroid (measured from the bottom), the moment of inertia & about the z axis, and the controlling section modulus S, about the z axis. (b) the bending stress O, at point H (positive if tension, negative if compression). (c) the bending stress y at point K (positive if tension, negative if compression). (d) the maximum bending stress, Omax produced in the cross section (positive if tension, negative if compression).