F = 200 N F3=300N M.: 100 Nm 0.4 m 300N 0.5 m 0.6 m The pipe system shown in the figure is supported by fixed joint at points O. Calculate the followings: (a) Replace the force-couple system acting on the pipe by a resultant moment and a single force acting on Point O.

F = 200 N F3=300N M.: 100 Nm 0.4 m 300N 0.5 m 0.6 m The pipe system shown in the figure is supported by fixed joint at points O. Calculate the followings: (a) Replace the force-couple system acting on the pipe by a resultant moment and a single force acting on Point O.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the internal force system acting on section 3 for the pin-connected frame. a P = 255 N (C), V = 0, M = 29.8 N · m b P = 255 N (T), V = 0, M = 29.8 N · m c P = 255 N (C), V = 0, M = 92.8 N · m d P = 525 N (C), V = 0, M = 29.8 N · m
A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with lengths L1 = 3.2 m and L2 = 3.9 m that are each attached to the plate by a clevis and pin (see figure). The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be s = 94.4' and a = 54.9° For these conditions, first determine the cable forces T1 and T2, then find the average shear stress Taver in both pin 1 and pin 2, and then the average bearing stress ?? between the steel plate and each pin. Ignore the weight of the cables.
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. 1.) Determine x-component of vector DF. 2.) Determine the y-component of Vector DF 3.) Determine the z-component of Vector DF. 4.) Determine the moment experienced by the system assuming that there is no wire support.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
Calculate the support reaction forces of the system given in the figure and draw the Norma Force (N), Shear Force (T) and Bending Moment (M) diagrams of the system. (In this question, M, N, T Equations will not be written.)
In the simple cage system in the figure, which of the following is the absolute value of the force carried by the CE element in kN?
Determine the internal forces at point D of the frame shown in the figure.
Consider the figure below where force P is applied at end A of the bar ABCD. 1. What is the magnitude of the moment of force P about point B? 2. What is the magnitude of the smallest force Q that can be applied at A to produce the same moment about B as the original force P?
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
A beam held by a hinge, take 2. The left end of a beam of mass 17.9 kg and length L is fixed to a wall by a hinge. The beam is inclined at 19.8 degrees from the horizontal; it is supported at its right end by a rope forming an angle of 30.3 kg with the horizontal.create a template for:a) the tension in the rope;b) the orientation of the hinge force, relative to the x+ axis.