Facing is an operation to reduce the diameter of work piece. Select one: True False

Q: Explain the process of aligning a hole working tool with the center of the workpiece.

A: The alignment of hole making tool with the center of work on the lathe machine . The workpiece is…

Q: Turning is a machining process in which a single-point tool removes material from the surface of a…

A: It is true that turning is a machining process in which a single-point cutting tool removes material…

Q: Give 1 example of methods of joint

A:

Q: Q4 Explain in detail the advantage of two of the following: a) Lubrication in metal forming b)…

A: a) Advantages of lubrication in metal forming In metal forming, lubricant will minimize friction and…

Q: Write the sequential procedure for making the simple step turning operation for making the shown job…

A: The sequence for making the simple step turning operation for making the shown job: 1. Centering 2.…

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: SUBJECT: machine Shop Theory and Practices 1.) How can we monitor and maintain the correct thread…

A: how can be monitor and maintain the correct thread pitch during threading operation?

Q: What is the working principle of shaper machine?

A: Shaper machine is type of machine tool which is used for material removal process by relative motion…

Q: In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: In multipoint cutting tools, the angle of the rake surface from the reference plane that is normal…

Q: What is the pitch of a ¼ inch bolt thread when the total number of thread is 30 for the total length…

A: Answer: The pitch of the bolt is 15 TPI (Threads Per Inch) or 1.7 mm.

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: Introduction for shaper work process please elaborate in 200 words

A: Shaper is a material removal machine of reciprocating type motion, and used for producing flat…

Q: Determine friction angle for metal cutting operation

A: To find Friction angle.

Q: In the following milling method, metal is cut by a cutter rotating in the same feed direction of…

A: Ans- b. Down milling.

Q: Why Cross-rail attachment is required in shaper?

A: Cross rail attachment is required beacuse

Q: 3.1 What would be the best type of jig for bending the patterns of the different sections of the…

A: given; what would be the best type of jig for bending the pattern of different section of the…

Q: IDENTIFY THE PARTS & FUNCTIONS OF LATHE MACHINE WITH PHOTOS.

A:

Q: What is central force?

A: central forces are basically those forces which are radially pointing, whose direction is along the…

Q: An engine lather is a power-driven , general-purpose machine tool used for ( a) measuring material…

A: Option b ic correct.

Q: A one machine shop producing bolts has a fixed cost of $2000 and a variable cost of $ 2 per bolts.…

A: solved

Q: With a neat sketch explain shaper machine

A:

Q: This is used tO correspond with machine tool usage where a working stroke would have high force…

A: ANSWER IS OPTION [ D] QUICK RETURN MECHANISM EXPLAINATION = QUICK RETURN MECHANISM IS USED IN…

Q: For wire drawing operation, the work material should essentially be (a) ductile (b) hard (C)…

A: A wire drawing is a process in which the diameter of wire is reduced in several steps and the most…

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? Shearing…

A:

Q: Question 4: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate…

A: Given data: dh=45 mmt=20 mmn=35 holes/nimE=7 N.m/mm2tc=110sec Need to determine the energy required…

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: Give some pictures illustrated about finishing under shaper work processes.

A: A shaper machine is a single-point cutting machine that Is used for machining the vertical and…

Q: the shaper machine work processes

A:

Q: During sheet metal working the Seam Joint is formed by folding of sheet metal.

A: During sheet metal working Seam joint is formed by folding of sheet metal. Answer: True

Q: Which cutting process does not produce a kerf space

A: When a cutting process takes place width of the cut produced is known as kerf space.

Q: Differentiate between Shaper and Planer Machine?

A: Shaper Machine                     Planer Machine Stroke length in the shaper…

Q: A work piece diameter is 30mm has been reduced to 27mm in turning process. Therefore one of the…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 9q      ___________________ is the lathe operation, which is performed without the cutting tool…

A: For thread cutting,  the tool post has to move automatically based on setting of gear box. Boring is…

Q: In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known…

A:

Q: -) With a neat sketch differentiate between counter boring and counter sinking operation.

A: As per bartleby guidelines we are allowed to solve only one question if multiple questions are…

Q: 8. is used most frequently when lifting or setting down loads, but they also occur in carrying,…

A: The answer to this question is Manual handling. It is a process in which a person uses part of his…

Q: Briefly describe the meaning of spark gap in wire cut machining by drawing a sketch.

A: Wire cut machining  The spark gap is the gap given between the conductors to pass an electric spark…

Q: In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt…

A: Drilling machine is a mechanical equipment used to introduce holes into a specimen which are in…

Q: In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as…

A: In lathe machine, type of feed is basically based on the movement of the tool. And this feed is…

Q: (c) State five factors which affect chip formation during metal cutting. (d) Outline the principle…

A: Chip Formation: Chip formation is a process that is associated with metal cutting with the help of a…

Q: In which lathe operation enlarging the already drilled hole can be produced.

A: Boring is a process in which a drilled hole made enlarged. It uses a single-point cutting tool.

Q: 8. Turning is a machining process in which a single-point tool removes material from the surface of…

A: The general process of turning involves rotating a part while a single-point cutting tool is moved…

Q: Force Pressure Area Area Pi Radius Radius Standard Units: Force is in Newtons (N), Pressure is in…

A:

Q: Question 1. The shaping machine is used to machine flat metal surfaces especially where a large…

A:

Q: A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads…

A: Given : f = 0.007 in/rev d = 0.1 in D = 3 in To find : The cutting speed for minimum cost per piece

Q: of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then…

A:

Q: Most sheet metalworking operations are performed as which of the following: O Cold working hot…

A: At room temperature only, the sheet metal operations are mostly done. As the sheet metals are mostly…