Question 1. The shaping machine is used to machine flat metal surfaces especially where a large amount of metal has to be removed. The shaper machine is a reciprocating type of machine basically used for producing the horizontal, vertical or flat surfaces. The shaper holds the single point cutting tool in ram and workpiece is fixed in the table. A shaper mechanism is designed to give a slow cutting stroke and a quick return to a blade attached to the slider at C. Determine the velocity of the slider block C at the instant 0= 60°, if link AB is rotating at 4 rad/s. 125 mm C 45 B WAR =4 rad/s 300 mm

Question 1. The shaping machine is used to machine flat metal surfaces especially where a large amount of metal has to be removed. The shaper machine is a reciprocating type of machine basically used for producing the horizontal, vertical or flat surfaces. The shaper holds the single point cutting tool in ram and workpiece is fixed in the table. A shaper mechanism is designed to give a slow cutting stroke and a quick return to a blade attached to the slider at C. Determine the velocity of the slider block C at the instant 0= 60°, if link AB is rotating at 4 rad/s. 125 mm C 45 B WAR =4 rad/s 300 mm

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter1: Introduction To Machining

Section1.1: Introduction To Machining

Problem 9RQ: What machine tool is available with either horizontal or vertical spindle orientation and uses...

See similar textbooks

Similar questions

If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in / rev and the depth of cut is 0.180 in, it determines: a) cutting time to complete the fairing operation; and b) the cutting speed; and c) The speed of metal removal at the beginning and end of the cut d) The power dissipated.
A two-spindle drill cuts two holes at the same time, one 1/2 inch and one 3/4 inch. The workpiece is 1.0 inches thick. Both drills have point angles of 118 degrees and the cutting speed for the material is 300 ft/min. The rotational speed of each drill can be set individually but the feed rate for both holes must be set to the same value because they move together into the material. The feed rate is set so that the total metal removal rate of both drills combined does not exceed 1.50 in3/min. Determine (a) maximum feed rate (in/min) that can be used, (b) individual feeds (in/rev) for each hole, and (c) cutting time for the operation.
For pocket operation of 2 x 3 inch surface and dept of 0.06 in using 0.5 in end mill tool. What is the time required to finished a cut when the depth of cut is 0.3 inch and the feed rate 0.05 inch/rev, spindle RPM is 60. The subject is Machine Shop Theory. Please make clear the solution and answer and understandable. Thanks
In a turning operation, the operator has established that a single pass on the cylindrical workpiece must be completed in 5.0 min. The piece is 400 mm long and 150 mm in diameter. Using a feed of 0.30 mm / rev and a depth of cut of 4.0 mm, what speed of cut should be used to meet this machining time?
Q#2 “Milling is an intermitted cutting operation”. Explain it.
In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?
Choose the most appropriate answers. The unit of cutting parameter "Feed"........ Conveyors designed within a restricted area is an example of........ Milling method in which the cutter axis is parallel to the machining surface is....
5.) Calculate the machining time required to reduce from 60mm diameter shaft to 50mm diameter, for a length of 1500mm with depth of cut 2mm for rough cut and 1mm for finish cut. Cutting speed and feed may be assumed as 30m/min and 0.5mm/rev respectively.
What machine tool is available with either horizontal or vertical spindle orientation and uses rotating cutting tools to primarily produce flat surfaces?
Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a feed rate of 0.004".
(a) Explain the difference between roughing and finishing operations in machining.(b) What are the parameters of a machining operation that are included within the scope of cuttingconditions?(c) What is the difference between threading and tapping?(d) A cylindrical workpiece is to be turned in a lathe. Determine the material removal rate if thecutting speed = 2.30 m/s, feed = 0.32 mm/rev, and depth of cut = 1.8 mm.(e) In a turning operation using high-speed steel tooling, the cutting speed = 110 m/min. The Taylortool life equation has parameters n = 0.140 and C = 150 (m/min) when the operation is conducteddry. When a coolant is used in the operation, the value of C is increased by 15%. Determine thepercent increase in tool life that will result if the cutting speed is maintained at 110 m/min.
A part to be turned in an engine lathe must have asurface finish of 1.6 mm. The part is made of a freemachining aluminum alloy. Cutting speed = 150 m/min,and depth of cut = 4.0 mm. The nose radius on the tool =0.75 mm. Determine the feed that will achieve thespecified surface finish.