A work piece diameter is 30mm has been reduced to 27mm in turning process.Therefore one of the following is correct.A. The depth of cut is 1.5mmB. The feed rate is 3mm.15.C. The feed rate is 1.5mm.D. The depth of cut is 3mm16.Facing operation is performed on?A. Drilling machine.B. Sawing machine.C. Milling machine.D. Lathe machine.17.The manufacturing process of removing material from the work piece is called.A. Milting and casting process.B. Machining process.C. Forming process.D. Extrusion processSpot welding is classified as:A. Thermit WeldingB. resistance weldingC. Friction weldingD. Arc WeldingTimber is the name given toa. Marking tool.b. SteelC. Glassd.18.19.WoodThe manufacturing process shown in the figure below is called?A. Spinning process.B. Turning process.C. Machining process.D. Bending process.20.

We are authorized to answer one question at a time, since you have not mentioned which question you…

A work piece diameter is 30mm has been reduced to 27mm in turning process. Therefore one of the following is correct. A. The depth of cut is 1.5mm B. The feed rate is 3mm. 15. C. The feed rate is 1.5mm. D. The depth of cut is 3mm

A work piece diameter is 30mm has been reduced to 27mm in turning process. Therefore one of the following is correct. A. The depth of cut is 1.5mm B. The feed rate is 3mm. 15. C. The feed rate is 1.5mm. D. The depth of cut is 3mm

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 2RQ: A lathe cross slide uses a diameter-reading micrometer collar. If the cross slide is advanced by...

See similar textbooks

Related questions

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

Q: What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm…

A: Given Data N=2409 rpm D=86 mm

Q: 45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed…

Q: Determine the optimum cutting speed for an operation on a lathe machine using the following…

Q: Show by a suitable sketch the rake and clearance angle of cutting tool in a machining work Also…

A: GIVEN DATA RAKE AND CLEARANCE ANGLE GIVEN WE HAVE TO SHOW IT ON DIAGRAM AND SIGNIFICANCE OF IT

Q: In a turning operation on carbon steel with hardness = 200 HB, the cutting speed = 250 m/min, feed =…

Q: 5. An engine lathe is used to turn a cylindrical work part, cutting speed 2.4 m/s, feed 0.20 mm/rev,…

Q: Show by a suitable sketch the rake and clearance angle of cutting tool in a machining work. Also…

Q: If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in /…

A: As the outer and inner diameter is not given so I am assuming it as D0 and Direspectivelya)…

Q: In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to…

A: Option b is correct.

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given D = 22 mm = 0.022 m Speed, N = 260 rpm

Q: an rpm that will produce the desired surface cutting speed of 125 fpm. The cutter diameter is 3 in.…

A: Given data: Surface cutting speed, u=125 fpm Feed per teeth, fz=0.006 in./tooth Cutter diameter,…

Q: A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine…

A: Given data Diameter of work piece = 55 mmLength of work piece = 200 mmFinal diameter = 45 mmCutting…

Q: A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine…

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: B/ A rectangular aluminum block is drilled at a depth of 40 mm using a drill that has two cutting…

Q: In orthogonal cutting if the depth of cut is a 1.25 mm and chip thickness after cutting is 2 mm,…

A: The cutting operation in which the angle between the cutting edge of tool and cutting velocity is 90…

Q: Q.4 (i) Find the time required for taking a complete cut on a plate 600 × 900 mm², if the .cutting…

A: As per the bartleby policy we can solve the only first question from the multiple questions. Q.4 (i)…

Q: The workpiece of size o 50 mm x 90 mm length is to be reduced to o 42 mm x 85 mm. If the depth of…

A: We have provided data from the question, Initial diameter= 50 mm; Initial length= 90 mm Final…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an…

A: there are 4 subparts posted in 1 question, as per honor code and answering guidelines I can answer…

Q: An end mill having 4 teeth is rotating at 250 RPM. If the feed per tooth is given as 0.1 mm, what is…

A: Given, z = 4 N= 250 RPM fz = 0.1 mm/teeth

Q: Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle…

Q: Q) An engine lathe is used to turn a cylindrical work part 150 mm in diameter by 500 mm long.…

A: GIVEN: D=150mm L=500mm F=0.3mm/rev d=3mm Cutting speed, V=2.5m/s=2500X60=150000mm/min a) CUTTTING…

Q: A cylinder is turned on a lathe with orthogonal machining principle. Spindle rotates at 200 rpm. The…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: 3.) A 3 inches diameter 5-tooth cemented-carbide-tipped face milling cutter is to use for milling a…

A: (a) The feed rate in inch per minute is 15.28 in/min. (b) The cutting time omitting the over travel…

Q: On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The lenght…

Q: is the lathe operation, which is performed without the cutting tool moving parallel to the axis of…

A: Lathe is a machine tool which is used in the work shop to perform the various machining operations…

Q: single-point cutting tool with 12° rake angle is used to machine a steel work-piece. The depth of…

A: Given:uncut thickness, t1=0.81 mmchip thickness, t2=1.8

Q: During orthogonal cutting of MS with a 15degree rake angle tool, the chip thickness ratio was…

A: As per given question Rake angle =15° Chip thickness =0.2 We have to determine shear angel

Q: What size is called actual? 1) the size obtained in the machining of parts and measured with an…

A: Answer - option (1) - the size obtained in the machining of parts and measured with an allowable…

Q: Q1 The tool signature of a single point cutting tool in NRS system is 15° – 10° – 5° – 10° – 25° –…

Q: (j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min,…

A: Given data : stainless steel with hardness = 200 HB cutting speed (v) = 250 m/min feed (f) = 0.3…

Q: A single point cutting tool designated as follows 8-14-6-6-6-20-1 is used to machine a work with…

Q: The rate of metal removal in drilling is determined as the product of the drill cross-sectional area…

A: Metal removal rate in drilling is given by:- πd^2×fN/4 where f is feed velocity and N is rpm And…

Q: In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as…

A: In lathe machine, type of feed is basically based on the movement of the tool. And this feed is…

Q: A straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel…

A: Given data: The feed rate is f = 0.2 mm/rev. The depth of cut is d = 0.5 mm. The side cutting edge…

Q: the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min…

A: Given, L = 120 mm d = 35 mm V = 30 m/min f = 0.7 mm/rev

Q: A part to be turned in an engine lathe must have a surface finish of 1.6 mm. The part is made of a…

Q: is the lathe operation, which is performed without the cutting tool moving perpendicular to the axis…

A: A lathe is a machine tool that holds and rotates a workpiece about an axis of rotation, and then…

Q: How nuch machlning time required a mild steel rod trom 65mm 58 mm over a length of 100 mm by turning…

A: Given Data ⇒ Initial Diameter of mild steel rod (D)=65 mm Length(L)=100 mm Approach Length(A)=5 mm…

Q: b) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm,…

Q: Identify the Lathe operation, performed without the tool moving parallel to the axis of the job is…

A: Different lathe operations are turning, facing, grooving, parting, threading, drilling, boring,…

Q: late the machining time to drill the flange as shown below. Take cutting speed 20 m/min, feed for 20…

A: Soln:- depth = 20 mm Number of Revolution required = depth/feed = 20/ 0.2 = 100 rev. V=…

Q: 1. A turning operation is performed on a cylindrical work part whose diameter 150 mm and length 375…

Q: Table 1 below shows the cutting speed for some common materials and the feed rates for various…

Q: D. 0.250" D, = 0.125" L-6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev;…

A: Cutting speed v=211 ft/minor v=211×12 =2532 in/minf=.0018 in/revD0=.250''Df=.125''L=6.250''

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

A work piece diameter is 30mm has been reduced to 27mm in turning process.
Therefore one of the following is correct.
A. The depth of cut is 1.5mm
B. The feed rate is 3mm.
15.
C. The feed rate is 1.5mm.
D. The depth of cut is 3mm
16.
Facing operation is performed on?
A. Drilling machine.
B. Sawing machine.
C. Milling machine.
D. Lathe machine.
17.
The manufacturing process of removing material from the work piece is called.
A. Milting and casting process.
B. Machining process.
C. Forming process.
D. Extrusion process
Spot welding is classified as:
A. Thermit Welding
B. resistance welding
C. Friction welding
D. Arc Welding
Timber is the name given to
a. Marking tool.
b. Steel
C. Glass
d.
18.
19.
Wood
The manufacturing process shown in the figure below is called?
A. Spinning process.
B. Turning process.
C. Machining process.
D. Bending process.
20.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I a orthogonal Turning lathe machine of diameter rod of 100 mm, Rake angle: +15°,Uncut chip thickness 0.5 mm, nominal chip thickness after the cut 1.25 mm. Find the shear angle.
List the different milling and lathe operations.
In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as________________________. A- taper feed B- cross feed C- longitudinal feed D- parallel feed
The following data is applicable for a turning operation. The length of job is 900 mm, diameter of job is 200 mm, feed rate is 0.25 mm/rev and optimum cutting speed is 300 m/min. The machining time (in min) is ___. A. 7.539 B. 7.90 C. 8.25 D. 9.00
In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as________________________. taper feed cross feed longitudinal feed parallel feed
A lathe mandrel is a hardened and tempered steel work-holding device.it is used for the further machining of a workpiece between centers after it has been bored or reamed while held in a chuck . The mandrel is ground to a taper of (a) 0.008 (b)0.006 (c) 0.005 (d) 0.007] inch per foot
Identify the name of the milling machine operation in which the cutting takes place by both the end face and periphery of the cutter body. Face milling Slab Milling Peripheral milling End milling
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
Differentiate lathe from milling.
Sawing machines can be divided into roughly four categories. They are _________________, ______________, ________________, and the ______________.
If 50 parts measuring 1" I" 3" each needed a hole drilled in a side, which workholding device would be best?
9q ___________________ is the lathe operation, which is performed without the cutting tool moving parallel to the axis of workpiece. Thread cutting Boring Operation Grooving Operation Counter Boring