Fig. given below shows a rigid bar ABC hinged at A and suspended at two points B and C by two bars BD and CE made of aluminium and steel respectively. The bar carries a load of 2000 kg midway between B and C. The cross-section area of the aluminium bar BD is 3 mm? and that of steel bar CE is 2 mm?. Determine the load taken by the two bars BD and CE. AB = 1m, BC =1m, %3D Ealuminium = 7000kg/mm? and Esteel = 20,000 kg/mm? ALUMINIUM ROD STEEL ROD 20co kg. im.

Fig. given below shows a rigid bar ABC hinged at A and suspended at two points B and C by two bars BD and CE made of aluminium and steel respectively. The bar carries a load of 2000 kg midway between B and C. The cross-section area of the aluminium bar BD is 3 mm? and that of steel bar CE is 2 mm?. Determine the load taken by the two bars BD and CE. AB = 1m, BC =1m, %3D Ealuminium = 7000kg/mm? and Esteel = 20,000 kg/mm? ALUMINIUM ROD STEEL ROD 20co kg. im.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please give right answer. A mid steel column 5 m long ad 50 mm dia.Which is fixed at end and free at the other end. Determine the Euler's crippling load. Take E = 2 * 10 ^ 5 * N / m * m ^ 2
A 11-m uniform beam is hinged to a vertical wall and held horizontally by a 5.0-m cable attached to the wall 4.0 mm above the hinge. The metal of this cable has a test strength of 1.00 kN, which means that it will break if the tension in it exceeds that amount. Part A: What is the heaviest beam that the cable can support with the given configuration? Express your answer in kilonewtons. Part B: Find the horizontal component of the force the hinge exerts on the beam. Express your answer in newtons. Part C: Find the vertical component of the force the hinge exerts on the beam. Express your answer in newtons.
The rigid bar AB with a length of 5m, is attached to two vertical rods and ishorizontal before the uniformly varying load of zero intensity at point A and 10kN/mat point B is applied. The rod at A is steel with L=3m, A=300 mm2 and E=200GPa. Therod in B is aluminum with L=4m, A=500mm2 and E = 70GPa. Determine the verticaldisplacement of the bar at a point where the resultant of the load is acting.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
A load of F = 14 kN is applied to a circular chain link shaped on the right. em = 600 N / mm2What is the diameter of the chain link in order to carry the given load safely?
A light ridig member AB is pinned at A and is further supported by light elastic rods CD and GF, member AB supports a 5000lb load at B the elastic modulus for the two elastic rods CD and GF is given as E= 30x106 psi and the cross-sectional area for each of these rods is 1 in2. what are the forces in the two supporting elastic rods as a results of the loading?
Load P is supported by levers ABC and DB as shown in the figure. Member DB is a truss member and has a square cross-section of 10 mm by 10 mm. If lever DB is made of 2014-T6 Aluminum, determine the maximum load P that can be applied. Take factor of safety 2. ? =100°
(i) A homogeneous prismatic bar hangs from a ceiling verticallydownwards under its own weight. The bar has density,?,Length, L and cross-sectional area, A. Show that the total elongation of the bar is given by Eq. (1):
SITUATION 3: The Fig shows a circular steel plate supported on 3 posts A, B, and C which are equally spaced along its circumference. A load P = 1,350 N is at a distance x = 0.5 m from the post at A along the x-axis. The diameter of the steel plate is 1.8 m. Neglecting the weight of the plate, what is the reaction at post A, in N? (Answer: 850) Neglecting the weight of the plate, what is the reaction at post B, in N? (Answer: 250) Considering the weight of the plate, what is the reaction at C, in N? The plate is 16 mm thick, and the unit weight of steel is 77 kN/m3. (Answer: 1295)
Two solid cylindrical rods support a load of P = 27 kN as shown. Rod 1 has a diameter of 16 mm and the diameter of rod 2 is 12 mm. Ø A. Determine the axial normal stress in Rod 1 (MPa). Ø B. Determine the axial normal stress in Rod 2 in MPa.
In the tree house the diameter of tree is 1m and the weight of house is 22 kN and the density of tree is 600 N/m^3 having a load that is distributed at 4.7 kN/m. The height of tree is 20 m and the house is built on top of it. A) Determine the internal load of tree? B) There is a weak point on tree at 5 m from the ground. The tree might break if the stress is high. Usually this type of tree fail if normal stress is greater than 200 kPa or the shear stress is greater than 50 kPa. Will this tree fail?
A steel column is of length 8m and diameter 600 mm with both ends hinged.Determine the crippling load by Euler’s formula. Take 5 E = 2.1x10 N/mm2