c) Figure 4 (c) shows two (2) 11 kV/415V distribution transformers are connectedusing 2 incomings with sectionalizing breakers at HV and LV side. brieflysummarize the switching procedure for maintenance personnel to shutdown theTransformer 2 for breaker servicing work at LV side and put back in-service.Supply line 1Supply line 2Disconnect switchDisconnect switchHV sidebreakerHV sidebreakerHV sectionilizingbreakerHV busleection 1HV bus section 2Transformer 1Transtormer 2Indoor switchgearLV sidebreakerLV sectionilizingbreakerLV bus section 1LV bus section 2FeedersbreakersOutcoming feedersFigure 4 (c)

Answered: Image /qna-images/answer/d2edacc9-dda5-449e-93e3-86bec84cacff.jpg

Figure 4 (c) shows two (2) 11 kV/415V distribution transformers are connected using 2 incomings with sectionalizing breakers at HV and LV side. briefly summarize the switching procedure for maintenance personnel to shutdown the Transformer 2 for breaker servicing work at LV side and put back in-service.

Figure 4 (c) shows two (2) 11 kV/415V distribution transformers are connected using 2 incomings with sectionalizing breakers at HV and LV side. briefly summarize the switching procedure for maintenance personnel to shutdown the Transformer 2 for breaker servicing work at LV side and put back in-service.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.2P

See similar textbooks

Similar questions

Using base values of 20 kVA and 115 volts in zone 3, rework Example 3.4.
How many transformers are needed to make an open-delta connection?
Rework Example 3.12 for a+10 tap, providing a 10 increase for the high-voltage winding.
a) Given the concept of Circuit Breakers discuss five types of circuit breakers and their principle of operation. b) the (1 Dimensional) design of the delta connected three phase Produce faults stated under (question 2ii). c) Using the (question 1.iv) parameters solve for the reactance in per unit(pu) quantity. CR d) Show the three criteria for the selection of a cable for power system distribution network.
A 25 MVA, II kV generator has X"d=0.2 p.u. X2 = 0.3p.u. and X0=0.1 p.u. Tht neutral of generator is solidly grounded. Determine the subtransient current in the generator and the line to line voltages for subtransient condition when a Y-B-G fault occurs at the generator terminals. Assume prefault currents and fault resistance to be zero.
5.The most frequently occurring fault in electrical power systems is Immersive reader. A) Symmetrical three-phase fault B) Line to ground fault C) Line to Line Fault D) Double Line to Ground Fault E) N. A.
Please do not give details answer only give as per question answer. Do not give wrong answer other wise ready for dislike. Also you solve type solution. Questions related Trasformer Selection of Trasformer 500 kva rating transformer which type tap switch use ? What is Rtcc ? What is Avr ? Also give What is CRT ?
(a) Which parameter is the most important in case of determining the rating of a circuit breaker and why? (b) In the given picture, would there be any difference in calculation of the transformers, if you choose primary or secondary side? Explain in words. Answer follow image.
30kV, 50MVA generator having a solidly grounded neutral and Z1 = 0.25pu, Z2=0.15pu and Z0=0.05pu. What reactance must be placed in the generator neutral to limit the fault current.
4.In a double line-to-ground fault we can expect thatImmersive reader A) There are currents in the ground connections. B) The current values in the ground connections are zero. C) Short-circuit currents exist in all three phases. D) The currents in the faulted phases are equal. E) N. A.
Which one of the following preliminary multistator watthour meter adjustments may be made while utilizing the series opposing connection of two current circuits ? A. Light-load adjustment B. Power factor adjustment C. Balance adjustment D. Full- load adjustment
1.a. To create usable voltages for 120-volt loads, _______ are usually installed.A. photovoltaic arraysB. transformersC. wind power turbinesD. generators1.b. Which grounding method is typically required of higher-voltage systems?A. Grounding through a high-impedance deviceB. Grounding through a low amount of resistanceC. Grounding through inductorsD. Grounding through surge arresters