I need help on this problem Figure 4 shows the balanced Wye-Wye connection of Three Phase Circuit. GivenVan= 310 V with a positive sequence of voltage source. The line impedance per phase isZ1 = 10 + j15 Q and load impedance per phase is Z2 =15 + j25 N. Calculate the line currents,%3Dline voltages, and load voltages.ZiZ2V anZ2Z2V bnV cnZ1ZiFigure 4

In balanced system,we can convert three phase to per phase equivalent circuit of phase a for easy…

Figure 4 shows the balanced Wye-Wye connection of Three Phase Circuit. Given Van = 310 V with a positive sequence of voltage source. The line impedance per phase is = 10 + j15 N and load impedance per phase is Z2 =15 + j25 N. Calculate the line currents, line voltages, and load voltages. Zi Z2 V an Z2 V en V bn Zi Zi Figure 4

Figure 4 shows the balanced Wye-Wye connection of Three Phase Circuit. Given Van = 310 V with a positive sequence of voltage source. The line impedance per phase is = 10 + j15 N and load impedance per phase is Z2 =15 + j25 N. Calculate the line currents, line voltages, and load voltages. Zi Z2 V an Z2 V en V bn Zi Zi Figure 4

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.25MCQ: For a balanced- load supplied by a balanced positive-sequence source. the line currents into the...

See similar textbooks

Similar questions

It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis after converting - load impedances to equivalent Y impedances. (ii) Base values can be selected either on a per-phase basis or on a three-phase basis. (a) Both statements are true. (b) Neither is true. (c) Only one of the above is true.
Figure 2.33 gives the general -Y transformation. (a) Show that the general transformation reduces to that given in Figure 2.16 for a balanced three-phase load. (b) Determine the impedances of the equivalent Y for the following impedances: ZAB=j10,ZBC=j20, and ZCA=j25. ZAB=ZAZB+ZBAC+ZCZAZCZA=ZABZCAZAB+ZBC+ZCAZBC=ZAZB+ZBAC+ZCZAZAZB=ZABZBCZAB+ZBC+ZCAZCA=ZAZB+ZBAC+ZCZAZBZA=ZCAZBCZAB+ZBC+ZCA
For a balanced- load supplied by a balanced positive-sequence source. the line currents into the load are 3 times the -Ioad currents and lag by 30. (a) True (b) False
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
A 400V three-phase, four wire system has the following loads connected: Phase 1: load impedance Z1 = 40 + j15 Ω Phase 2: load impedance Z2 = 60 Ω Phase 3: load impedance Z3 = 15 – j20 Ω I am just looking for the working out for phase 2 - please ignore the other phases The line and phase voltages for all phases (including phase angles) The line and phase currents for all phases (including phase angles) The neutral current (including phase angle)
1. Three impedances Z1, Z2 and Z3 are delta-connected to a symmetrical 3-phase, 400 V supply of phase sequence RYB. Z1 = (8 – j 6) Ω and is connected between lines R and Y. Z2 = (6 + j 8) Ω and is connected between lines Y and B. Z3 = (10 + j 0) Ω and is connected between lines B and R. Calculate (i) line and phase currents (ii) power per phase (iii) total power. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages. Repeat for a case when the same loads are now connected in star.
A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to abalanced-∆ load with Z∆ = 30 ∠40o Ω. The line impedance between the source and load is ZL = 1 ∠850 Ω.for each phase. Calculate the line currents, the ∆ -load currents, and the voltages at the load terminals.Recall that ZY = Z∆/3
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 132.7906 volts with an-bn-cn sequence. This source has an internal series impedance of 0.2+j2.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 18-j10; Zbn = 15+j25; Zcn = 20+j30 ohms. If there is a line-to-line fault at lines b and c load-side, what is the magnitude of the fault current in amperes?
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 132.7906 volts with an-bn-cn sequence. This source has an internal series impedance of 0.2+j2.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 18-j10; Zbn = 15+j25; Zcn = 20+j30 ohms. If line a is open creating a series fault at line load-side, what is the magnitude of the line current in line b in amperes?
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 120 volts with an-bn-cn sequence. This source has an internal series impedance of 0.1+j1.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 40+j30; Zbn = 36-j15; Zcn = 18+j24 ohms. If there is a single-line-to-ground fault at line a load-side, what is the magnitude of the fault current in amperes?
The one-line diagram of a three-phase power system is as shown in the figure attached. Impedances are marked in per unit on a 100-MVA, 400-kv base. The load at bus 2 is S(sub 2) = 15.93 MW - j33.4 Mvar, and bus 3 is S(sub 3) = 77MW + j14 Mvar. I tis required to hold the voltage at bus 3 at 400 angle 0 degrees kV. Working in per unit, determine the voltage at buses 2 and 1.