Figure Q2 shows a beam subjected to distributed loading. Knowing the beam is fixed supported at one end and roller supported at the other end; (a) Draw the Free Body Diagram (FBD) of the beam (b) Sketch the possible elastic curve of the beam (c) Define the elastic curve formulation y of the beam using Macaulay Function (d) Define support reactions of the beam

Figure Q2 shows a beam subjected to distributed loading. Knowing the beam is fixed supported at one end and roller supported at the other end; (a) Draw the Free Body Diagram (FBD) of the beam (b) Sketch the possible elastic curve of the beam (c) Define the elastic curve formulation y of the beam using Macaulay Function (d) Define support reactions of the beam

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
Draw the shear force and bending moment diagrams of the given simple headstock beam? can you solve it step by step!
A 70kg human steps at the tip of a springboard used to dive in a pool. The springboard has a length of 1.75 meters, moment of inertia is 0.000002 m^4, and modulus of elasticity is 150 GPa. Determine the deflection of the springboard in millimeters. Note: δ=[(W)(L^3)]/[(3)(E)(I)] for a cantilever beam with end force.
Draw the Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for a loaded simply supported beam shown below. 1KN 4KN
For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. Label the diagrams properly and provide values at all key points within the diagrams.
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where Mo = 10,800 kip-in, P = 1205 lb, F = 1.25 kip, Wa = 2750 lb/ft, Wb = 1.055 kip/ft, a = c = 7 ft, b = 12 ft.
There is a doubly embedded circular beam, (diameter = 60cm) and (G=2x10⁴ kg/m²) It is requested:a.-Calculate the value of the maximum torque.b.- Build the torsion angle diagram only HANDWRITTEN answer needed ( NOT TYPED)
Draw the Shear Force and Bending Moment Diagram for the loaded simply supported beam shown below. Ignore the self-weight of the beam
For the loaded beam shown below , Estimate the Reaction Values of supports
Compute the reactions of the supports of beams; 1. AB 2. CD 3. EF 4.GH 5. IJ 6. KL
A uniform, 7.5-m-long beam weighing 6490 N is hinged to a wall and supported by a thin cable attached 1.5 m from the free end of the beam. The cable runs between the beam and the wall and makes a 40° angle with the beam. What is the tension in the cable when the beam is at an angle of 30° above the horizontal?
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.