Fill out the table below for each fluid with a common flow velocity of 20 m/s flowingthrough a 20 cm? opening and a common temperature of 70°C.fluidP (kg/m³)т (kg/s)enthalpy(kJ/kg)total flowenergy (kJ/kg)sat. liquid watersat. vapor watersat. liquid R-134asat. vapor R-134aair at 1 atm (useTable A-17)

Answered: Image /qna-images/answer/466cfeb7-898d-4735-8022-9b80279f6994.jpg

Fill out the table below for each fluid with a common flow velocity of 20 m/s flowing through a 20 cm? opening and a common temperature of 70°C. fluid P (kg/m³) ṁ (kg/s) enthalpy (kJ/kg) total flow energy (kJ/kg) sat. liquid water sat. vapor water sat. liquid R-134a sat. vapor R-134a air at 1 atm (use Table A-17)

Fill out the table below for each fluid with a common flow velocity of 20 m/s flowing through a 20 cm? opening and a common temperature of 70°C. fluid P (kg/m³) ṁ (kg/s) enthalpy (kJ/kg) total flow energy (kJ/kg) sat. liquid water sat. vapor water sat. liquid R-134a sat. vapor R-134a air at 1 atm (use Table A-17)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Similar questions

Air enters a fan through a duct at a velocity of 6.5 m/s and an inlet staticpressure of 2.5 cm H2O less than atmospheric pressure. The air leaves the fan through aduct at a velocity of 11.5 m/s and a discharge static pressure of 7.62 cm H2O above theatmospheric pressure. If the specific weight of air is 1.20 kg/m3 and the fan delivers 9.45m3/s, determine the fan theoretical power and the fan efficiency when the power input tothe fan is 13.75 kW at the coupling?
[CE Hydraulics] 5. For the case of turbulent flow in rough pipes, does the friction factor depend on the Reynolds number? Why?
Assuming the clearance is negligible for a single stage compressor with the followingdata.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1. What is the power input to the compressor if compression is isentropic in kW to 3 decimal places? 2. What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (? = 999.7 kg/m3 and ? = 1.307 × 10−3 kg/m·s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss.
In quantity flow measurement using pitot tube, is it necessary to get the average velocity? Why?
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
What are the basic parameters for calculating of Jet Pulse Compress Air for cleaning of bags from dust in Bag Filters and Bag Houses?
A small centrifugal pump is used to pump 30-Celsius water at the rate of 6 L/s with ahead of 44.54 m. If the diameter of the pump is 20 cm and operate at 1200 rpm,determine;(i) head coefficient,(ii) capacity coefficient, and(iii) power coefficient. also the same small centrifugal pump is used to pump water at same rate but with a temperature of 15-Celsius. determine in which condition (15-Cor 30-C) is the pump perform better in term of;(i) power out, and(ii) pump efficiency.Justify your answer.
What is the friction loss in cm of water in a 2.44m diameter chimney 61m high up which gas is flowing at 9.14 m/sec? Gas density is 0.6776 kg/m3.
Pressure Drop of Power-Law Fluid in Laminar FlowA power-law fluid having a density of 1041 kg/m3 is flowing through 14.9 m of a tubing with an inside diameter of 0.0524 m at an average velocity of 0.0728 m/s. The rheological or flow properties of the fluid are K′ = 15.23N·sn′/m2 (0.318 lbf·sn′/ft2) and n′ = 0.40. Calculate the pressure drop and friction loss using Eq. (9.1-10) for laminar flow. Check the generalized Reynolds number to make sure that the flow is laminar. Repeat part (a) but use the friction-factor method
Assuming the clearance is negligible for a single stage compressor with the followingdata.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1. What is the power input to the compressor in kW to 2 decimal places if the compression is polytropic compression process with n=1.25? 2. What is the delivery temperature of air for an isentropic compression process in Kelvin to 1 decimal place? 3. What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s) from holding tank to filling a machine at a mass flow rate of 2 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diamter sanitary pipe between the holding tank and the filling machine, wiht one open globe valve and four regular 90° flanged elbows in the system. Within the system, there is a heat exchange which causes 100 kPa of pressure drop due to friction. The holding tank is open to atmosphere, and filling machine is running at a pressure of 1.5 atm. The diamter of the filling machine pipe is 3cm. A: What is the volume flow rate of the system? B: What is the diamete of the pipe? C: What is the average velocity inside the pipe? D: What is the reynolds number of the flow in the pipe? E: What is the flowing type?