For oil (SG = 0.86. u = 0.025 N-s/m? ) flow of 0.24 m/s through a round pipe with diameter of 521 mm, determine the Reynolds number. Is the flow laminar or turbulent? (a) What is the flow area? (b) What is the flow velocity? (c) What is the density of the fluid? (a) A = m2 (b) V= m/s (c)p- kg/m? (a) What is the Reynolds number? (b) Is the flow laminar, transitional or turbulent? (a) Re = (b) The flow is |

For oil (SG = 0.86. u = 0.025 N-s/m? ) flow of 0.24 m/s through a round pipe with diameter of 521 mm, determine the Reynolds number. Is the flow laminar or turbulent? (a) What is the flow area? (b) What is the flow velocity? (c) What is the density of the fluid? (a) A = m2 (b) V= m/s (c)p- kg/m? (a) What is the Reynolds number? (b) Is the flow laminar, transitional or turbulent? (a) Re = (b) The flow is |

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil of density 950 kg/m³ and viscosity 1E-2 Pas is to be pumped 10 through a pipeline and the pressure drop must not exceed 2E5 Pa. What is the minimum diameter of pipe which will be suitable, if a flowrate of 50 tonne/h is to be maintained? Assume the pipe wall to be smooth. A. 0.025 mB. 0.175 mC. 0.855 mD. 0.008 m
Sketch the shear stress and velocity distribution for laminar flow across a pipe section?
What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter 0.2 m, transporting oil (density 900 kg/m3 and viscosity 0.5 Pa-s) at a flow rate of 100 kg/s from sea level to an elevated height 10 m above sea level? What is the viscous pressure drop along the pipe?
A 1/4” inside diameter pipe is used to transport SAE 30 motor oil (µ = 0.006266 slug/ft-s and ρ =1.7267 slug/ft3) over a distance of 100 ft. Assuming that the pipe is horizontal and the flow throughit is steady, laminar, and fully-developed, what gauge pressure must a pump develop at the head ofthe pipe to provide a flow rate of sufficient to fill a quart bottle every 5 seconds? [6291 psi] Whatis the Reynolds number (based on diameter) for this flow? [112.5] Is the assumption of laminar flowreasonable?
Flow In Closed Conduits 2. Water at 25C flows through a 200-mm diameter new cast iron pipe at a velocity of 2 m/s if the pipe is 720 m long, determine the head lost due to friction using Darcy – Weisbach formula. Answer: _______________________________
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
A pipe 100mm bore carries oil of density 900 kg/m3 at a rate of 4 kg/s. thepipe reduces to 60mm bore and rises 120m. the pressure at this point isatmospheric (zero gauge) assume no frictional losses.Determine:The volume per secondThe velocity at each sectionThe pressure at the lower end The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.What does the magnitude of the Reynolds number mean to fluid flow
For water flowing in a pipe of 8 inches diameter at 65 oC and 0.01 ft3/s, what will be the entry length (Le) needed for water flow to be described as fully developed flow? What does that tell you about the length of the tube you should select in your design?
A 500 mm diameter pipe gradually reduces to 20 mm diameter and the gradually enlarge to its original size. Given the pressure at the base of the convergence of 0.60 MPa with a flow of 0.08 cu. m/s, 1. What is the velocity at point 1? 2. What is the velocity head at point 2? 3. Neglecting the head loss, the pressure of the smallest section is?
An oil with density of 900 kg/m2 and viscosity of 0.0002 m2/s flows upward through a 10 m long pipe segment inclined at 40℃ with the horizontal. The pressure a the upstream and downstream end of the pipe are 350 kPa and 250 kPa, respectively. The diameter of the pipe is 60 mm. Assume the flow is laminar. What is the head loss along the pipe segment? 3.77 4.9 5.35 6.1 What is the velocity of the fluid flow? 3.37 2.95 2.08 2.7 Which of the following gives the Reynold’s number? 810.9 624.21 1011.15 885.63
Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a diameter of 35 mm. If the acid flow rate is 1.55 m3 / min, what is the pressure loss due to friction in a 30 m long smooth pipe? a. Reynold number = b. Loss of Pressure =
If a dust-proofing oil at 30°C had been flowing at 0.046 m /s through a 150-mm pipe in which along-radius flow nozzle 75 mm in diameter, what would have been the deflection of the mercury? Assume C=0.98.