Find the breaking point along the fishing rod assuming that the base of the rod is in a fixed position and will not move. The rod is made out of Carbon fiber with diameters a-9.93 mm wide, b-7.13mm wide, and c=5.1mm wide. The total length of the rod is 2 meters. The modulus of elasticity of Carbon Fiber is 228 Gpa. Find what force "F" is needed to break the fishing rod assuming that the force is acting straight along the line. |

Find the breaking point along the fishing rod assuming that the base of the rod is in a fixed position and will not move. The rod is made out of Carbon fiber with diameters a-9.93 mm wide, b-7.13mm wide, and c=5.1mm wide. The total length of the rod is 2 meters. The modulus of elasticity of Carbon Fiber is 228 Gpa. Find what force "F" is needed to break the fishing rod assuming that the force is acting straight along the line. |

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.14P: A rigid bar AB having a mass M = 1.0 kg and length L = 0.5 m is hinged at end A and supported at end...

See similar textbooks

Similar questions

Five bars, each having a diameter of 10 mm. support a load P as shown in the figure. Determine the plastic load Ppif the material is clastoplastic with yield stress
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Wires B and C are attached to a support at the left-hand end and to a pin-supported rigid bar at the right-hand end (see figure). Each wire has cross-sectional area A =0.03 in2 and modulus of elasticity E = 30 X 106 psi. When the bar is in a vertical position, the length of each wire is L = 80 in. However, before being attached to the bar, the length of wire B was 79.98 in. and wire C was 79.95 in. Find the tensile forces TBand Tc in the wires under the action of a force P = 700 lb acting at the upper end of the bar.
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
Three prismatic bars, two of material A and one of material B. transmit a tensile load P (see figure). The two outer bars (material A) are identical. The cross-sectional area of the middle bar (material B) is 50% larger than the cross-sectional area of one of the outer bars. Also, the modulus of elasticity of material A is twice that of material B. (a) What fraction of the load P is transmitted by the middle bar? (b) What is the ratio of the stress in the middle bar to the stress in the outer bars? (c) What is the ratio of the strain in the middle bar to the strain in the outer bars?
A steel wire- and an aluminum allay wire have equal lengths, and support equal loads P (see figure). The moduli of elasticity for the steel and aluminum alloy are Ea= 30,000 ksi and Ea= 11,000 ksi, respectively. (a) IF the wires have the same diameters, what is the ratio of the elongation of the aluminum alloy wire to the elongation of the steel wire? (b) If the wires stretch the same amount, what is the ratio of the diameter of the aluminum alloy wire to the diameter of the steel wire? (c) If the wires have the same diameters and same load P, what is the ratio of the initial length of the aluminum alloy wire to that of the steel wire if the aluminum alloy wire stretches 1.5 limes that of the steel wire? (d) If the wires have the same diameters, same initial length, and same load P. what is the material of the upper wire if it elongates 1.7 times that of the steel wire?
A rigid bar AB having a mass M = 1.0 kg and length L = 0.5 m is hinged at end A and supported at end B by a nylon cord BC (see figure). The record has cross-sectional area A = 30 mm2. length b = 0.25 m. and modulus of elasticity E = 2.1 GPa. If the bar is raised to its maximum height and then released, what is the maximum stress in the cord?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
*16 A prismatic bar AB of length L, cross-sectional area A, modulus of elasticity E, and weight Changs vertically under its own weight (see figure). (a) Derive a formula for the downward displacement Scof point E. located at distance It from the lower end of the bar. (b) What is the elongation SBof the entire bar? (c) What is the ratio £ of the elongation, of the upper half of the bar to the elongation of the lower half of the bar? (d) If bar A B is a riser pipe hanging from a drill rig at sea. what is the total elongation of the pipe? Let L = 1500 m, A - 0.ol57 m2, and E = 210 GPa. See Appendix 1 for weight densities of steel and sea water. (See Probs. 1.4-2 and J.7-13 for additional figures.)
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.