Find the equivalent force-couple system at point P for the force system shown below if F = 600 N. 2.0 m 4.0 m - 2.0 m- - 2.0 m- P 3.0 m 2000 N 1000 N Beer, 2011 O a. Xp = 600 N, Yp = 2000 N, Mp = 0 O b. Xp = 2000 N, Yp = 500 N, Mp = 0 O c. Xp = 2000 N, Yp = 600 N, Mp = 100 N.m O d. Xp = 600 N, Yp = 2000 N, Mp = 200 N.m

Find the equivalent force-couple system at point P for the force system shown below if F = 600 N. 2.0 m 4.0 m - 2.0 m- - 2.0 m- P 3.0 m 2000 N 1000 N Beer, 2011 O a. Xp = 600 N, Yp = 2000 N, Mp = 0 O b. Xp = 2000 N, Yp = 500 N, Mp = 0 O c. Xp = 2000 N, Yp = 600 N, Mp = 100 N.m O d. Xp = 600 N, Yp = 2000 N, Mp = 200 N.m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.14P: Find the internal force system acting on section 3 for the pin-connected frame.

See similar textbooks

Similar questions

The resultant couple moment for all the forces shown in the figure below is?
d=1.50m, cable doesnt stretch and length of it between the 2 springs is 1.80m, frictionless system. m is mass of hanging weight and mp is mass of pulley.
The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
1 ! SHOW COMPLETE SOLUTION ! * DRAW FBD *pls answer manually Problem 1: The pulleys are frictionless and of negligible weight A 250 kg 300 kg C B 450 kg Find: A. Tension (N) in the cord supporting block B. B. Acceleration at Block A (m/s^2) C. Acceleration at Block B (m/s^2) D.Acceleration at Block C (m/s^2)
refer to the illustration below. The frictional effects of the air on the blades of the standing fan creates a couple moment of M0 = 7 joules on the blades. what could be the magnitude of the couple forces at the base of the fan so that the resultant couple moment on the fan is zero. choices are: 30.00N 33.33N 16.67N 26.67N 23.33N
The figure shows a control bar, subjected to a force of 90N. Since the length of the bar is 225 mm and the moment of the clockwise force on B is 13.5 N.m, determine the value of α. Solve the problem using scalar notation and explain your result.
The flat plate shown in Figure is acted on by the three couples. Replace the three couples with a couple-vector.
In the mechanism shown, find the force P and all reaction forces. Ignore weight forces and friction
A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 20 in. The generator output is 40 Hp, 3600 rpm and 90% efficiency. If there are 10 bolts, determine the force acting on each bolt in kN.
Two equivalent force-couple systems are shown below. If M1 and M2 are 300 and 20 lb-ft, respectively, calculate forces S and Q (both in lb) and the dimension d (in ft). Note that the sense of S and Q are assumed only. Also, the magnitudes of forces P1=53.98N and P2=580.2N
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity. b = 0.4 m, d =0.5 m , t =0.1 m.a) The aerodynamic center is 0.1 m from the y axis (neutral axis). Calculate thetwist angle caused by the lift force. b) Calculate the reactions at the fixed end. c) Assume the engine applies a torque around the x – axis of the spar of 100 kN-m,calculate the angular delfection of the wing at x = 3 m due to the engine.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.