O16 ll zain IQCapture.PNG →PROBLEM-6 (HW)The system consisting of the bar O.1, two identical pulleys,and a section of thin tape is subjected to the two 1SO-N tensile forces shown in thefigure. Determine the equivalent force-couple system at point O.180 Nr= 25 mm100 mm180 N4550 mm29...

Answered: Image /qna-images/answer/d8e8ecfe-b3ba-49bc-a6f4-1feec9fc5157.jpg

PROBLEM-6 (Hw)The system consisting of the bar O.1, two identical pulleys, and a section of thin tape is subjected to the two 180-N tensile forces shown in the figure. Determine the equivalent force-couple system at point O. 180 N r= 25 mm 100 mm 180 N 45 50 mm

PROBLEM-6 (Hw)The system consisting of the bar O.1, two identical pulleys, and a section of thin tape is subjected to the two 180-N tensile forces shown in the figure. Determine the equivalent force-couple system at point O. 180 N r= 25 mm 100 mm 180 N 45 50 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.15P: The structure is supported by a pin at C and a cable attached to A. The cable runs over the small...

See similar textbooks

Related questions

Q: The flat plate shown in Figure is acted on by the three couples. Replace the three couples with a…

A: dear student please rate me postive :) Stay safe stay happy ! There are total three couples in…

Q: A truss of span 10 meters is loaded as shown in the figure. Find the forces in all the members of…

A: we are unable to solve these questions by two methods .please post again the second method problem…

Q: The link ABC shown in Figure Ql is pin connected at B and rests against a smooth support at A. i.…

Q: Problem 2. Considering a 20 kg bar as shown in the figure: a) find angle theta and the reactions to…

A: Consider NA as the reaction at point A, NB as the reaction at point B, fB be the frictional force…

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: Given Force = 160 N a = 85 mm d = 150 mm h = 165 mm Theta = 19o To find Moment at point O Distance d…

Q: A spring with a constant equal to 15 KN/m is connected to points C and F of the mechanism shown in…

A: Free Body Diagram

Q: Homework: The pin-connected structure of Figure below has the 2400 N.mm moment applied to member…

A: The reaction at E needs to be solved

Q: The ABO vertical arm, whose weight of mass m is neglected in the figure, is kept in balance with a…

A: Given, Pipe OAB in equilibrium Mass m =610 kg.

Q: The system consisting of the bar OA, two identical pulleys, and a section of thin tape is subjected…

Q: Problem 2. For the Plane frame shown in figure, determine the axial force in cord (DE) and the…

Q: Determine the forces and internal moment at points 1 and 3 indicated in the figure. Consider the…

Q: Problem 3: The wrench shown in the figure below is used to tighten a bolt at A. If the wrench does…

A: To determine the moment about A and also the reactions.

Q: The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a…

A: Given, P=800 lb

Q: The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN,…

A: Note: As per the policy, we can solve the first 3 subparts. Please resubmit the remaining parts.

Q: Question 2 The member ABC which is supported by a smooth collar at A, rocket at B and short link CD…

A: In the given figure, point A is supported by the smooth collar, point B is hinged, and point C is…

Q: A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with…

A: Given data as per question dimensions of steel plate = 2.5 x 1.5 x 0.08 m weight of steel plate=…

Q: Practice Problem 4.4.13: Find the magnitudes of the pin reactions at A, C, and E caused by the…

A: Given Moment at centre Mo=180 lb.ft radius of disk r= 2ft To Find: Reactions at A, C and E

Q: Calculate the support reactions at point A and B, and the forces at the hinges (C, D and E) of the…

A: The free-body diagram of the plane frame is shown below.

Q: The dual-grip clamp shown in the figure is used to provide added clamping force with a positive…

A: Given data as per question clamping force =3.7 kN Considering free body diagram

Q: The member ABC which is supported by a smooth collar at A, rocket at B and short link CD as shown in…

A: Given: The beam with the loads is shown below:

Q: Q4-Two blocks A and B of weight 350 N and 600 N. respectively are connected by a cord that passes…

Q: 2.A boom AB is supported in a horizontal position by a hinge A and a cable which runs from C over a…

A: The Hinge at A gives the horizontal and the vertical reaction. Considering the triangle ACD…

Q: A vertical force F of 176 N is applied to the bell crank at point A as shown in the figure below. A…

Q: Problem 4: Consider the two-dimensional truss given in the figure below. If the maximum force that…

Q: Question 2 75 lb В The bar AB is connected to bars CD and EF with two smooth collars. At A, the…

Q: A bracket is subjected to the force-couple system shown in the figure below. Determine the reactions…

A: The free body diagram of the system is as follows:

Q: 3.18. A block with a mass of 150-kg is supported by a cable which passes over a 150-mm diameter…

A: Given Data Mass of the block is : m=150 kg Diameter of pulley is :d=150 mm Now from the free body…

Q: In the figure below, set up an equation related to the moment (M) about the paired force (F).

Q: Problem Number 3: The block shown in the figure below is acted on by its weight, W = 650 KN, a…

Q: Sample Problem 22: Combine the two forces Pand T, which act on the fixed structure at B, into a…

Q: Sample Problem 2/10: The rigid structural member is subjected to a couple consisting of the two 100…

Q: Determine the reaction at pin B in N. Determine the horizontal component of reaction at pin A in N.…

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: The given force in vector is The position vector of the force can be determined as shown below.

Q: Problem 4.129 Two systems of forces and moments act on the beam. Are they equivalent? System 1 50…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: в 1 m 1 m 1 m 1m 1m 1 m 1'kN 1 kN

Q: The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 30 kN,…

A: Note: As per the policy, we can solve the first 3 subparts. Please resubmit the remaining parts.

Q: Q4) Calculate the force T in the cord at C needed to support the loaded truss. Also, find the forces…

A: Force Force is vector quantity which has magnitude and direction. Force is a rate of change of…

Q: Problem 3: The system consisting of the bar OA, two identical pulleys, and a section of thin tape is…

Q: . From the system shown in the figure, obtain the forces and the average axial stres on each bar AB,…

Q: Problem 2. For the Plane frame shown in figure, determine the axial force in cord (DE) and the…

Q: PROBLEM-6 (HW)The system consisting of the bar 0.4, two identical pulleys, and a section of thin…

Q: Four sets of flexible cables, spaced at 120° intervals, are used to stabilize a 400-ft…

A: Draw the free body diagram of the section containing point A: The axial force transmitted through…

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

Q: Problem 4.129 Two systems of forces and moments act on the beam. Are they equivalent? System 1 50…

Q: For nos. 1-3, consider the system shown wherein force P = 250N and couple M = 100 N-m. Assuming a =…

Q: In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: block with a mass of 150-kg is supported by a cable which passes over a 150-mm diameter pulley that…

A: given : The mass of the block = 150 kg The diameter of the pulley = 150 mm

Q: Problem 2. For the Plane frame shown in figure, determine the axial force in cord (DE) and the…

A: Moment (M) at point D: 29 kN.m Vertical Load at D: 7 kN Horizontal load on member BE: 10.5 kN

Q: Replace the single force of Figure below by horizontal force through B, a vertical .force through A,…

A: Given data

Q: The system consisting of the bar OA, two identical pulleys, and a section of thin tape is subjected…

Concept explainers

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,

Question

O16 ll zain IQ
Capture.PNG →
PROBLEM-6 (HW)The system consisting of the bar O.1, two identical pulleys,
and a section of thin tape is subjected to the two 1SO-N tensile forces shown in the
figure. Determine the equivalent force-couple system at point O.
180 N
r= 25 mm
100 mm
180 N
45
50 mm
29
...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The structure is supported by a pin at C and a cable attached to A. The cable runs over the small pulley D. Find the internal force systems acting on sections 1 and 2.
The 1800lbin. couple is applied to member DEF of the pin-connected frame. Find the internal force systems acting on sections 1 and 2.
The uniform 10 kg rod AB is supported by a ball and socket joint at A and by the cord CG that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B and that the tension in the cord CG, TCG=52.1 N, determine the following a.) Which of the following best shows the equivalent force-couple set at point A of the tension at cord CG, TCG? Choices: a F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 11.03 Nm j b F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 29.4 Nm k c F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 11.03 Nm j d F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 29.4 Nm k b.) Which of the following moments is equal to zero? Choices: The moment of the tension in cord CG, TCG about point OThe moment of the tension in cord CG, TCG about point AThe moment of the tension in cord CG, TCG about point BThe moment of the tension in cord CG, TCG about axis AB
Joint O of a space frame is supported by spring OA and is subjected to three member forces. Member 1 lies in the x-z plane while member 2 lies in the x-y plane. If the magnitude of the force in member 1 is 200N, which of the following best approximates the magnitude of the force exerted by member 3, F3 on joint O? Show free body diagram.
One end of a post weighing 400 Nand with height h rests on a roughhorizontal surface with ms = 0.30.The upper end is held by a ropefastened to the surface and makingan angle of 36.9° with the post. A horizontal force F isexerted on the post as shown. (a) Ifthe force F S is applied at the midpointof the post, what is the largest value it can have without causing the postto slip? (b) How large can the force be without causing the post to slip ifits point of application is 6/10 of the way from the ground to the top of thepost? (c) Show that if the point of application of the force is too high,the post cannot be made to slip, no matter how great the force. Find thecritical height for the point of application.
6b. Find out all possible FBD/FBDs to solve for all the components of the support forces exerted by the pin supports A and B to the frame assembly. 6c. If the applied force F=320N and couple moment M=230N*m, determine the magnitude of the support reaction at pin B. Answer must include 1 place after the decimal point and have the proper unit.
A force of P=280 N is applied on semicircular rod at point B. Determine internal forces at point J if θ=30°. (draw free body diagram)
Topic: Couples, Resultant of Force Systems & Equilibrium If F1 = 10N, F2 = 15N, F3 = 8N, F4 = 10N, F5 = 18N, and the length of te side of a red square is 1m. Calculate magnltude (+ for CCW, - for CW) of the resuItant moment (N-m) about point A. Calculate the magnitude of the reItant f0rce (N). (Answer: 50.80Nm, 20.33N)
Find the forces at all joints of the structure.
TEXTBOOK PROBLEM The resultant of the forces P1, P2, and the couple C is the force R= 35.6k N acting at a point A (R is not shown in the figure). Determine P1, P2 and C
W2 acts at the center G of the bar. Find the cables' tensions and the reactions at ball and socket O. W1 is 515 N. W2 is 190 N.
Determine force-couple system at A, C , and D and provide a free body diagram at them points.