The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at Ti corresponding convection coefficient is h; = 30 W/m2.K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is To = -25°C and the associated convection coefficient is h, = 65 W/m²-K? Evaluate the properties of the glass at 300 K. 40°C and the 00,0 Tsi i °C T5,0 i °C = S.0

The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at Ti corresponding convection coefficient is h; = 30 W/m2.K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is To = -25°C and the associated convection coefficient is h, = 65 W/m²-K? Evaluate the properties of the glass at 300 K. 40°C and the 00,0 Tsi i °C T5,0 i °C = S.0

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.45P

See similar textbooks

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
1.13 If the outer air temperature in Problem is –2°C, calculate the convection heat transfer coefficient between the outer surface of the window and the air, assuming radiation is negligible.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
Calculate the heat loss per square foot of wall surface for a wallmade of 1-in. of plaster and 9-in. of common brick. The air velocityover the surface of the brick is 15 mph; the outside air temperature is40 °F, and the surface temperature of the plaster facing the room is 70°F.s
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at T∞,i=40°C and the corresponding convection coefficient is hi=30 W/m2·K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is T∞,o= -27.5°C and the associated convection coefficient is ho=65 W/m2·K? Evaluate the properties of the glass at 300 K. a. what is Ts, i in °C? b. what is Ts, o in °C?
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at T∞,i=40°C and the corresponding convection coefficient is hi=30 W/m2·K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is T∞,o= -27.5°C and the associated convection coefficient is ho=65 W/m2·K? Evaluate the properties of the glass at 300 K. a. what is the heat flux through the original walls in W/ m^2? b. what is the heat flux through the retrofitted walls in w /m^2?
Chips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosurewhose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity ofε=0.60 and a maximum allowable temperature of Ts=85oC.(a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operatingpower of each chip? The convection coefficient may be approximated as h=11.7 W/m2K.(b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forcedconvection, with h=250 W/m2K, what is the maximum operating power?
Question 1: A glass window of width W = 1 m and height H = 2m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 °C and -20 C, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of (last two digit of your Registration number) °C and -15 °C, what is the rate of heat loss from a 1 mx2mwindow? The thermal conductivity of air is ka = 0.024 W/m.K.
The rear window of an automobile is defogged by pass- ing warm air over its inner surface. (a) If the warm air is at T ,i 40 C and the correspond- ing convection coefficient is hi 30 W/m2 K, what are the inner and outer surface temperatures of 4-mm-thick window glass, if the outside ambient air temperature is T ,o 10 C and the associated con- vection coefficient is ho 65 W/m2 K? In practice T ,o and ho vary according to weather conditions and car speed. For values of ho 2, 65, and 100 W/m2 K, compute and plot the inner and outer surface temperatures as a function of T ,o for –30 T ,o 0 C.
Question 1: A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 oC and -20 oC, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of 20 oC and -15 oC, what is the rate of heat loss from a 1 m x 2 m window? The thermal conductivity of air is ka = 0.024 W/m.K.
In the design of electronic components, it is very desirable to attach the electronic circuitry to a substrate material that is a very good thermal conductor but also a very effective electrical insulator. If the high cost is not a major concern, what material would you propose for the substrate?