Answered: : Find the resultant of the force…

Engineering

Civil Engineering

: Find the resultant of the force system shown in Fig 2. 100 N 15 cm 30 N 20 N 20 cm A 45° 5 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: d) e) f), with full solution

A: d) The yield point is the point on a stress-strain curve that indicates the limit of elastic…

Q: 2) The simply supported beam with a channel cross-section carries the loads as shown. Determine the…

Q: Compute the Principal stresses and max shearing stress and their direction at Point (A) shown in…

Q: Determine the amount of water needed to achieved the normal consistency of 650 grams cement by using…

A: The amount of water required to be mixed in cement to make a cement paste such that when the sample…

Q: oads as shown. Determine the maximum flexural st a) in tension D) in compression 30 kN 200m 60 kN/m…

Q: 2. Determine the reaction at the supports using E- 70 GPa and 1=1,300,000,000 mm^4. determine the…

Q: shown? 900N/m A किन 2m Im 3m 3 Ans/S=2940 N.M²³ EI

A: As there are two different questions posted, according to the guidelines, only the first is being…

Q: 3. A 25-ft wide river running 22-feet deep is impinging on the upstream side of a bridge but not on…

A: Solution-The given values are as follows,The width of the river(w)=25ftThe depth of the river (d)=22…

Q: 8. Resultant force on a 1 mx 1 m gate immersed vertically at a depth of 2 m below the free water…

Q: Am 8 kN/m ΒΙΣ 2m Figure 7 C

Q: H.W3 Determine the slope and deflection of end A of the cantilevered beam. E= 200 GPa and…

A: Given data E= 200 GPa I = 65.0 x 106 mm4 here, a dummy concentrated load is applied in the…

Q: 4) An overhanging beam carries the load as shown in the figure. a) Select the lightest W shape that…

Q: H.W3 Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I =…

Q: (Triangulation): Two stations B and C were observed from a theodolite set up A and following data…

Q: Symmetrical T-beam with a span of 6m The clear distance to adjacent beams is 3m. Web width = 250mm…

Q: EXERCISES Determine the y-coordinate of the centroid of the shaded area in terms of h. !h/2 x

Q: Use Nevilles Interpolation x=6

A: Neville's method use the Newton polynomial form to assess a polynomial that runs through a specified…

Q: find the value of deflection at the Position midway between the suffe and at the overhanging end by…

A: Given :

Q: Fill in the blanks d: - 1 attachment Initial velocity of the ball, vo 29.50 m/s, upward from the…

Q: To what the distance object to be displaced. Lo that work done is 1205. Man of box 32kg Farce…

A: Work done is the product of force and displacement caused by that force. Mathematically, W = F x s…

Q: screen was made of wire 5mm in diameter with 2mm square apertures. The screen, inclined at 15°, had…

Q: Design the one-way slab to support a load of 12 kN/m² with a superimposed dead-to-live load ratio of…

Q: 8.4. Determine the cost to install 126 tons of structural steel given the following infor- mation:…

Q: Fill in the blanks A: B: Mass of plane: 22,000 kg Tension, T: 400 N Determine the reactions at A and…

Q: Q.6 Over taking time required for a vehicle with design speed of 50 kmph and overtaking acceleration…

Q: A 200 g/l solution of common salt was discharged into a stream at a constant rate of 25.. 1/s. The…

Q: 5) Select the lightest W310 that can resist the given loads as shown in the figure. Use the table…

Q: What is the total settlement of the clay layer five years after the completion of primary…

A: This question is from Geo technical engineering

Q: As shown in Fig. 2. Find the reaction at A R Hinge 3 m Atmospheric pressure Stop Water 6 m 30 Fig.…

Q: It is proposed to adopt the dilution method of stream gauging for a river whose hydraulic properties…

Q: Determine the reaction at the supports using E= 70 GPa and I = 1,300,000,000 mm^4. Use excel…

A: Applying three moment equation to span (1) and span…

Q: $) 20KN -14 kN/m 14 kN/m F bb ↓ ↓ ↓ ↓ E L L L 3 (21) 20kN 4m 5m 5m Q-Solve the frame using the angle…

Q: D 55° YE f. sm C 55° 2500N 85 do 10m *

Q: 2) The simply supported beam with a channel cross-section carries the loads as shown. Determine the…

Q: Determine the magnitude of the maximum hear force on the inclined member in kN?

Q: The dilution method with the sudden-injection procedure was used to measure the dis-... charge of a…

Q: (Trilateration): In a trilateration network one of the triangles has the following data: AB = 600m,…

Q: beam section is limited to a width of 250mm and a total depth of 550mm. The beam is subjected to a…

Q: For the beam shown in figure, find the deflection and rotation at Free end by using double…

Q: 9- If the coefficient of static friction between the crate and the ground is s= 0.3, determine the…

Q: Determine area the top and all side of a platform below. 6m 2.65m 115°

Q: From an instrument set up an object was observed at a distance of 5.4 km away. Neglecting the effect…

Q: The dilution method with the sudden-injection procedure was used to measure the dis- charge of a…

A: Given: The weight of the dye is 300 N. The concentration measurement data are,

Q: Material Strengths: Fy=345 MPa, Fu = 483 MPa The channel (C230X30) is connected with four M20 bolts…

Q: Instructions: Solve the following problems as instructed. Boxed final answers and round off to the…

Q: A bracket in the figure below has two forces exerted on it. a. Sketch the two forces and the…

Q: 298.5 kN 3.2m 3.2m 3.2m 3.2m 3.2m T P L H ôm Å S 0 Y G B 4m R N J F em с M 1 E D

A: Solution: Given: a) Point of contraflexure occurs at the middle points of the points of the various…

Q: Estimate the capillary soil suction using the Green-Ampt equation if it takes 3.5 hours for an…

A: Given, t = 3.5 hrs L = 40 cm or 0.4 m η = 0.20 i = 2.5 cm/hr

Q: A beam section is limited to a width of 250mm and a total depth of 550mm. The beam is subjected to a…

Q: II. STEEL 1. Define the Tension test for rebars 2. Enumerate and explain different methods of…

A: The tension test for rebars has to be defined, the different testing methods of steel have to be…

Question

= Find the resultant of the force system shown in Fig 2.
100 N
15 cm
30 N
20 N
20 cm
A
45° 1
5 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
determine the resultant of the forces : A = 800N at 40degrees , B=600N at 160degrees and C=200N at 300 degrees
Determine the resultant of the force system shown in fig. and its x and y intercepts.
The frame shown supports a mass of m=250kg mass suspended from point F. The frame is supported by a pin connection at Point A and a roller at Point D. Internal pin connections are located at Points B, C, and E. The dimensions of the frame are h1=0.7m, h2=1.6m, h3=0.5m, L1=1.2m, L2=0.4m. Determine: The vertical and horizontal components of the reaction force at Point A. The vertical and horizontal components of the force at Pin C. The reaction force at Point D.
What is the mass M that must be suspended at the leftto hold the system in equilibrium in the position shown? SHOW COMPLETE FBD
In the beam loaded as shown in the figure, 4. Find the reaction at the left support. a. 36 kN b. 25 kN c. 15 kN d. 35 kN 5. Find the absolute max shear a. 41 kN b. 71 kN c. 90 kN d. 105 kN 3. Find the location of maximum positive beam moment measured from point a. a. 4.437 m b. 5.437 m c. 1.732 m d. 2.273 m
Determine the total force in kN on a circular plate of diameter 1.5 m whcih is placed vertically in water in such a way that center of plate is 2 m below the free surface of water. CHOICES: a.35.67 b.59.34 c.103.0 d.44.14
Calculate the force on element AB and GH of the Howe structure shown in the figure.
P-1. In the figure 1 shown, w 1 = 36 N/m, w2 = 30 N/m, w3 = 15 N/m, a = 4.5m, b = 3m, c = 2m. Calculate the following: a. The magnitude of the resultant force in N. b. The moment about O in N-m. c. The location of the resultant force from O in meters.
2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the unknown tension T, which acts on the braked pulley. 275 N 1600 N 0.5 1.5 m- 1.8 m m 300 N A 1.25 m B 50° 0.6 m 650 N
The load at A creates a force of 60 lb in wire AB. Express this force as a Cartesian vector acting on A and directed toward B as shown.
Determine the internal forces at point J of the structure shown in the figure.