Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a cutting speed of 16 meter /minute. Spindle speed in rpm= Answer

Q: 1.To mill material having a cutting speed of 40 fpm. What should be the RPM of 1.25 inches diameter…

A: Velocity, V= πDN12, where, V= Velocity in fpmD= Diameter in inches (12 is divided in the above…

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

A:

Q: i. spindle rpm ii. feed speed iii. cutting time iv. material removal rate

A:

Q: what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25…

A: Given data, S = 80 stroke/min L = 1.25 feet = 15 in Find Cutting speed = V

Q: Turning tests have resulted in 1 min tool life at a cutting speed = 4.0 m/s and a 20 min tool life…

A:

Q: How is spindle aligmment done in a milling machine?

A: By spinning a cutting tool (cutter) and sliding it into the work item, a milling machine removes…

Q: Q4 Tool life of a turning tool is given by VTO.12xx=C_at a cutting speed (V) of 25m/min, feed(f)…

A:

Q: 9. Write the formula for calculating spindle speed in revolution per minute for milling machine,…

A: GIVEN DATA-  A MILLING OPERATION QUESTION ASKED  WE HAVE TO WRITE SPINDLE SPEED RELATION

Q: 1. What type of milling machine can be used to make the groove in the shaft? 2. The diameter of the…

A: 1. Grooves, elongated slots and break-throughs are produced or made for the purpose of receiving…

Q: Question 2 Briefly explain the following chips formation in machining operation with the help of…

A:

Q: a orthogonal Turning lathe machine of diameter rod of 100 mm, Rake angle: +15°,Uncut chip thickness…

A: Given values:Orthogonal turning is given,Rake angle,α=+15odiameter of rod,d=100 mmuncut chip…

Q: For a drilling operations, the feed per revolution is 0.08 mm / rev and the spindle speed is…

A:

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given data: The cutting speed of the tool is v=22 mmin The feed of the tool is f=0.2 mmrev The depth…

Q: )Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given d=22mm=0.022m spindle speed N=210rpm

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A:

Q: Find the spindle speed in rpm, if the slotting operation is performed by 16mm end mill with a…

A: Manufacturing processes: The various processes that are involved in converting raw material into a…

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 186.00 m/min and…

A: Find the spindle speed  Cutting speed = 186 m/sec External diameter = 38.50 mm

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A:

Q: D d a° L1 SI. Parameter in Dimension in No: Drawing mm 1 d 35 2 L1 28 Cutting speed (Cs) in m/…

A:

Q: Choose the right answer - In turning, the cutting force that increases by decreasing depth of cut…

A: In turning operation the cutting force is the resultant of tangential force, feed force, and radial…

Q: Determine the number of strokes per minute at which the shaper should run to machine a piece of…

A: The number of strokes per minute at which the shaper should run to machine a piece of copper is 96…

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A:

Q: State the equations used to calculate: (a) The rotational speed in rpm b) The feed rate in in/min.…

A: In machining process There is requirement of calculation   (a) The rotational speed in rpmb) The…

Q: The figure shows the part drawing of turning exercise in lathe machine. a) List out the operation…

A: The turning operation is performed on the lathe machine.the various operations perform in lathe…

Q: B/ A rectangular aluminum block is drilled at a depth of 40 mm using a drill that has two cutting…

A:

Q: 1. List the operations and the tools needed to make the following shape. 2. Find the speed of…

A: 1. operations and the tools needed to make the following shape are listed below:

Q: Find the machining time to complete the job as shown below from the basic raw material of 50 mm…

A: Given: L = 100 mm Di = 50 mm Vt = 25 m/min Vd = 20 m/min f (for turning and boring) = 0.5 mm/rev f…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: The blade on a typical table saw rotates at 3100 revolutions per minute. Calculate the linear…

A: Calculated the linear velocity in miles per hour of one teeth at the edge of the 10 inch diameter…

Q: A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an…

A: there are 4 subparts posted in 1 question, as per honor code and answering guidelines I can answer…

Q: Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle…

A:

Q: A mild steel specimen of  Initial diameter of  30.5 mm is turned to final diameter of 27 mm for an…

A: Turing is a material removal operation in which the diameter of the workpiece is reduced. It…

Q: 3.) A 3 inches diameter 5-tooth cemented-carbide-tipped face milling cutter is to use for milling a…

A: (a) The feed rate in inch per minute is 15.28 in/min. (b) The cutting time omitting the over travel…

Q: 1. Explain with a sketch any 4 different types of centers used on a lathe machine?

A: There many types of centres used on a lathe machine those are 1.Dead center or Live center. 2.Soft…

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

A:

Q: List the methods of taper turning on lathe machine. Explain different taper turning methods. State…

A: list of methods of taper turning on lathe machine       1.Form tool method      2.Tailstock set…

Q: Explain any three parts of a milling machine.                                           b) Explain…

A: Milling machines  Milling machines are a type of machinery for removing material from a workpiece…

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 107.00 m/min and…

A:

Q: D d. a° L1 El. Parameter in Dimension in lo: Drawing mm d 35 L1 28 |Cutting speed (Cs) in m/ minute…

A:

Q: 14. Determine the proper RPM for a 3" piece of cold-rolled steel with a cutting speed of SFPM. Round…

A: We will answer the first question since the exact one was not specified. Please submit a question…

Q: (a)Find number of passes to finish the entire turning operation (b) Total time required to complete…

A: for solution refer below images.

Q: the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min…

A: Given, L = 120 mm d = 35 mm V = 30 m/min f = 0.7 mm/rev

Q: The blade on a typical table saw rotates at 3850 revolutions per minute. Calculate the linear…

A:

Q: Q2 -Calculate the taper angle if the major diameter is 40.00mm and minor diameter is 28.00. The…

A:

Q: Milling is an intermitted cutting operation”. Explain it.

A: A milling machine is a machine tool that cuts metal as the workpiece is fed against a rotating…

Q: late the machining time to drill the flange as shown below. Take cutting speed 20 m/min, feed for 20…

A: Soln:- depth = 20 mm            Number of Revolution required = depth/feed = 20/ 0.2 = 100 rev. V=…

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given dataCutting speed Vc = 22m/minFeed f = 0.2mm/revolutionDepth of cut d = 0.5mmTaper angle α =…

Q: Using the formula (below), calculate the revolutions per minute (rpm) a drill press spindle should…

A: The diameter of the twist drill is D=12 ft. The cutting speed of the drill is V=90 ft/min.

Q: 6. Compute for the necessary stroke per minute on 8 inches copper if it has 100 fpm as its cutting…

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.